16 views
in Synchronous machine by
In relation to the synchronous machines, which on of the following statements is false ? 

(A) In salient pole machines, the direct-axis synchronous reactance is greater than the quadrature-axis synchronous reactance. (B) The damper bars help the synchronous motor self start. (C) Short circuit ratio is the ratio of the field current required to produces the rated voltage on open circuit to the rated armature current. (D) The V-cure of a synchronous motor represents the variation in the armature current with field excitation, at a given output power.

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

In relation to the synchronous machines, which on of the following statements is false ? 

(A) In salient pole machines, the direct-axis synchronous reactance is greater than the quadrature-axis synchronous reactance. (B) The damper bars help the synchronous motor self start. (C) Short circuit ratio is the ratio of the field current required to produces the rated voltage on open circuit to the rated armature current. (D) The V-cure of a synchronous motor represents the variation in the armature current with field excitation, at a given output power.

Related questions

0 answers 16 views

A pair of synchronous machines on the same shaft may be used to generate power at 60 Hz from given source of power at 50 Hz. Using minimum number of poles for both the machines, the synchronous speed will be (a) 500 r.p.m. (b) 600 r.p.m. (c) 1000 r.p.m. (d) 1200 r.p.m. 

asked May 25, 2018 in Synchronous machine by Shimroz123
0 answers 23 views

Which of the following is false for switch statement in C++?  (1) It uses labels instead of blocks (2) we need to put break statement at the end of the group of statement of a condition (3) we can put range for case such as case 1..3 (4) None of these

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 42 views

When two synchronous machines are connected in parallel the synchronizing power tends to (A) accelerate the faster machine (B) retard the faster machine (C) retards the slower machine (D) pull the faster machine out of step

asked Jun 4, 2018 in Synchronous machine by Shimroz123
1 answer 16 views

V - curve of synchronous machine shows the relation between?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 15 views

Which of the following statement is false? Modulation is used to: (1) Reduce the bandwidth used (2) Separate differing transmissions (3) Ensure that intelligence may be transmitted over long distances (4) Allow the use of practicable antennas

asked May 29, 2018 in Electronics communication by Shimroz123
1 answer 29 views

The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 24 views

A cylindrical rotor synchronous motor is switched on to the supply with its field windings shorted on themselves, the motor will .  A) Not start B) Start but will not run at synchronous speed C) Start as an induction motor and then run as a synchronous motor D) Start and run as a synchronous motor

asked May 20, 2018 in Synchronous machine by Shimroz123
1 answer 19 views

With regard to the expressive power of the formal relational Query languages, which of the following statements is TRUE?  A) relational algebra is more powerful than relational calculus B) relational algebra has the same power as relational calculus C) relational algebra has the same power as safe relational calculus D) None of these

asked Apr 11, 2018 in Computer Engineering by Shimroz123
0 answers 19 views

Which of the following statements with reference to a generic microprocessor is correct?  a. Instruction cycle time period is exactly equal to machine cycle time period  b. Instruction cycle time period is shorter than machine cycle time period   c. Machine cycle time period is shorter than instruction cycle time period  d. Instruction cycle time period is exactly half of machine cycle time period

asked Apr 9, 2018 in Microprocessors and Microcontrollers by Shimroz123
1 answer 15 views

Which of the following relation is incorrect? A) capacity factor = utilization factor x load factor B) load factor x maximum load = average load C) demand factor x connected load = maximum demand D) none of these

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

Consider the following statements with regard to Lissajous pattern on a CRO :  1. It is a stationary pattern on the CRO.  2. It is used for precise measurement of frequency of a voltage signal.  3. The ratio between frequencies of vertical and longitudinal voltage signals should be an integer to have a steady Lissajous pattern.  Which of the above statements is/are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

Which of the following statements is not valid in case of conductors in electrostatic fields? A) The static electric field intensity inside a conductor is zero B) The static electric field intensity at the surface of a conductor is everywhere directed normal to the surface C) The conductor surface is an equivalent potential surface D) None of the above

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

In a DC machine, which of the following statements is true ?  (A) Compensating winding is used for neutralizing armature reaction while interpole winding is used for producing residual flux (B) Compensating winding is used for neutralizing armature reaction while interpole winding is used for improving ... winding is used for neutralizing armature reaction (D) Compensation winding is used for improving commutation while interpole winding is used for producing residual flux

asked May 17, 2018 in DC machine by Shimroz123
0 answers 26 views

If the RF transmission is terminated in its Characteristic impedance Z, which of the following statements is wrong : a. The input impedance of transmission line becomes Zc. b. The transmission line acts as an infinite long transmission line. c. The VSWR becomes one d. The VSWR becomes infinite

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 31 views

Which one of the following statements is correct? Digital modulation techniques are used in satellite communication systems since:  (1) They are easier to handle (2) Large bandwidth utilization is possible (3) They have a higher spectral efficiency (4) They are less prone to interference

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 7 views

Which of the following statements pertains to resistors only ?   (a) They oppose sudden change in voltage. (b) They can act as energy storage device. (c) They can dissipate desired amount of power. (d) None of the above. 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

Which machine is the exciter of synchronous machine?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 17 views

The damping winding in synchronous motor is generally used to?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 9 views

Consider the following statements with regard to induction type wattmeter :  1. Can be used on both ac and dc systems.  2. Power consumption is relatively low.  3. It is accurate only at stated frequency and temperature.  Which of the above statements is/are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Consider the following statements regarding capability curves of a synchronous generator :  1. The MVA loading should not exceed the generator rating.  2. The field current should not be allowed to exceed a specified value determined by field heating.  3. The MW loading should not exceed the rating of the prime mover.  4. The load angle must be more than 90°.  Which of the above statements are correct ?

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Which statement is INCORRECT in relation to NYQUIST and BODE analyses ? (A) Number of closed-loop poles in the right-half S-plane can be determined using Nyquist Criterion. (B) Bode analysis uses two plots, one for magnitude and another for phase angle. (C) Nyquist analysis uses two plots, one for magnitude and another for phase angle. (D) Relative stability can be assessed from both Nyquist and Bode analyses.

asked Apr 25, 2018 in Control System by Shimroz123
1 answer 24 views

If we change the excitation of synchronous machine will it affect on power factor?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 18 views

If we change the excitation of synchronous machine will it affect on motor speed?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 19 views

The back emf of synchronous motor depends on?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 13 views

Which of the following statements is incorrect? A) During parallel resonance impedance at resonance is minimum B) During parallel resonance current is magnified C) During series resonance current at resonance is maximum D) During series as well as parallel resonance, the power factor is unity

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Which statement out of the following statements about ‘corona’ is incorrect? A) Corona gives rise to radio interference B) Corona results in loss of power in transmission C) Corona discharge can be observed as red luminescence D) Corona is always accompanied by a hissing voice

asked Jun 4, 2018 in Power system by Shimroz123
1 answer 13 views

For a single phase capacitor start induction motor, which of the following statements is valid?  A) The capacitor is used for power factor improvement B) The direction of rotation can be changed by reversing the main winding terminals C) The direction of rotation cannot be changed D) The direction of rotation can be changed by interchanging the supply terminals

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 18 views

Which of the following statements is wrong for transistor biasing methods:  1. The base resistor method does not provide stabilization of operating point 2. The biasing with feedback resistor provides only some stabilization 3. Base resistor method provides better stabilization than collector feedback method 4.Voltage divider bias is widely used because it has stable operating point

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 20 views

Which of the following statements is true?  (1) steady-state stability limit is greater than transient stability limit  (2) steady-state stability limit is equal to transient stability limit  (3) steady-state stability limit is less than the transient stability limit  (4) no generalization can be made regarding the equality or otherwise of the steady-state stability limit and transient stability limit

asked Apr 29, 2018 in Switchgear And Protection by Shimroz123
1 answer 56 views

Which of the following statements is not characteristic of a static magnetic field? (A) It is solenoidal. (B) It is conservative. (C) It has no sinks or sources. (D) Flux lines are always closed.

asked Apr 28, 2018 in Physics by Shimroz123
1 answer 29 views

Which of the following statements is incorrect ? (A) Superposition theorem is useful for Linear and Non-linear circuit analysis when several sources are present in the circuit. (B) Thevenin's equivalent network consists of one voltage source in series with an impedance. (C) Norton's equivalent network consists of ... . (D) When both the load and source impedances are purely resistive, maximum power transfer is achieved under the condition : Load Resistance = Source Resistance

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 14 views

For a rotameter, which one of the following statements is TRUE? (A) The weight of the float is balanced by the buoyancy and the drag force acting on the float (B) The velocity of the fluid remains constant for all positions of the float (C) The measurement of volume flow rate of gas is not possible (D) The volume flow rate is insensitive to changes in density of the fluid

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 27 views

Which of the following statements is CORRECT?  (A) A grid-connected induction generator always supplies lagging reactive power to the bus. (B) An overexcited synchronous motor draws current at a lagging power factor. (C) An under excited synchronous generator connected to an infinite bus works at a leading power factor. (D) The load angle of a synchronous machine is the angle between the excitation voltage and the load current.

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

Which of the following statements is not correct ? (A) A primary cell is an electro-chemical cell (B) After charging, a primary cell can be again put to use (C) Dry cell is a primary cell (D) Leclanche cell is used in experiments, where constant supply of current is not needed

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
0 answers 36 views

The maximum torque which a synchronous motor will develop at rest for any angular position of the rotor, at rated stator supply voltage and frequency, is known as?

asked Mar 20, 2018 in Synchronous machine by Shimroz123
1 answer 12 views

In transformers, which ofthe following statements is valid?  A) In an open circuit test, copper losses are obtained while in short circuit test, core losses are obtained B) In an open circuit test, current is drawn at high power factor C) In a short circuit test, current is drawn at zero power factor D) In an open circuit test, current is drawn at low power factor

asked May 17, 2018 in Transformer by Shimroz123
1 answer 21 views

In a synchronous motor which losses varies with load?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 28 views

The number of electrical degrees ‘passed through’ in one revolution of a 6-pole synchronous alternator is: A) 360 degree B) 720 degree C) 1080 degree D) 2160 degree

asked Jun 17, 2018 in Synchronous machine by Shimroz123
1 answer 11 views

The angle δ in the swing equation of a synchronous generator is the  (A) angle between stator voltage and current (B) angular displacement of the rotor with respect to the stator (C) angular displacement of the stator mmf with respect to a synchronously rotating axis. (D) angular displacement of an axis fixed to the rotor with respect to a synchronously rotating axis

asked May 17, 2018 in Synchronous machine by Shimroz123
1 answer 38 views

What is the maximum value of torque angle in synchronous motor?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 13 views

Consider the following statements with regard to a GTO : 1. The turn-off gain of the GTO is large. 2. Large negative gate current pulses are required to turn off the GTO. 3. GTO has large reverse blocking capability. Which of the above statements is/are correct ? (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Consider the following statements. Which of these statements are correct ?  (1) Reactance relays are preferred for ground fault relaying  (2) Impedance relays are most suitable for:protecting long transmission lines  (3) Mho relays are best suited for long transmission line protection  (4) Reactance relays are widely used for protection of Medium transmission lines  (A) All of them (B) (1) and (3) (C) (2) and (4) (D) (1), (2) and (4)

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 11 views

Which of the following statements are correct regarding dot product of vectors ?  1. Dot product is less than or equal to the product of magnitudes of two vectors.  2. When two vectors are perpendicular to each other, then their dot product is non -zero.  3. Dot product of two vectors is positive or negative depending whether the angle between the vectors is less than ... the codes given below :  (a) 1, 2 and 3 only (b) 1, 3 and 4 only (c) 1, 2 and 4 only (d) 2, 3 and 4 only

asked Apr 25, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,471 questions

7,069 answers

134 comments

3,088 users

...