Can you help by answering this question?

The auxiliary power consumption in a thermal power plant is

22 views
in Electrical Machine by
The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be 

(A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

1 Answer

+2 votes
by

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be 48.0%

Related questions

1 answer 30 views

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

asked May 8, 2018 in Electrical Machine by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is

asked May 8, 2018 in Electrical Machine by Shimroz123
0 answers 19 views

A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each conductor is 0.5 ohm / km. Receiving end voltage is 33 kV. If the line loss is not to exceed 10%, determine the length of the line.  (A) 7 km (B) 27.9 km (C) 56.8 km (D) 13.9 km

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

asked Mar 21, 2018 in DC generator by Shimroz123
1 answer 36 views

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

asked May 3, 2018 in Electrical Machine by Shimroz123
0 answers 13 views

 A single phase, 2000V alternator has armature resistance and reactance of 0.8 ohm and 4.94 ohm respectively. The voltage regulation of the alternator at 100A, 0.8 leading pf is (A) 7% (B) - 8.9% (C) - 6.3% (D) 0%

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in rpm will be: (A) 1080 (B) 1203 (C) 1000 (D) 1200

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 39 views

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

asked May 3, 2018 in Electrical machine design by Shimroz123
1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

asked Apr 29, 2018 in Electrical Machine by Shimroz123
0 answers 45 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 7 views

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately? A.385 ohms B.38.5ohms C.3.1 ohms D.31 ohms

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 17 views

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately equal to: A. 385Ω B. 38.5Ω C. 3.1Ω D. 31Ω

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

asked May 22, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 21 views

A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to a 120 V, 60 Hz source. From a wattmeter test, it is known that iron losses are equal to 180 W. Calculate the reactive power absorbed by the core.  (A) 600 var (B) 572 var (C) 180 var (D) 360 var 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load armature reaction weakens the main flux by 5%. Whereas the armature circuit voltage drops by 10%. The full load speed of the motor is (a) 1200 r.p.m. (b) 1080 r.p.m. (c) 1040 r.p.m. (d) 1000 r.p.m.

asked May 25, 2018 in DC motor by Shimroz123
0 answers 14 views

A single phase motor draws a current of 5 A from a 120 V, 60 Hz line. The power factor of the motor is 65%. Calculate the active power absorbed by the motor.  (A) 600 W (B) 390 W (C) 456 W (D) 650 W 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

A permanent magnet stepper motor with 8 poles in stator and 6 poles in rotor will have a step angle of (a) 7.5° (b) 15° (c) 30° (d) 60°

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 56 views

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) inversely proportional to α and Φ (C) directly proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 9 views

When running under no-load condition and with over excitation, armature current Ia drawn by a synchronous motor

asked May 15, 2018 in Electrical Machine by Shimroz123
1 answer 33 views

A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be (A) 23.06 kW (B) 24.11 kW (C) 25.01 kW (D) 26.21 kW

asked May 17, 2018 in Electrical Machine by Shimroz123
1 answer 117 views

The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

asked Apr 28, 2018 in Electrical Machine by Shimroz123
1 answer 25 views

The following motor definitely has a permanent magnet rotor  (A) DC commutator motor (B) Brushless dc motor (C) Stepper motor (D) Reluctance motor

asked May 17, 2018 in Electrical Machine by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

The efficiency of a transformer at full load 0.8 p.f lagging is 90%. Its efficiency at full load 0.8 p.f leading will be (1) Less than 90% (2) More than 90% (3) 90% (4) None of these 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

When a dipole antenna of 1/8 length has an equivalent total resistance of 1.5 Watt then the efficiency of the antenna is   (A) 0.89159% (B) 8.9159% (C) 89.159% (D) 891.59%

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 14 views

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
2 answers 114 views

Advantages and Disadvantages of Permanent Magnet Brushless DC (PMBLDC) Motor

asked Aug 9, 2017 in Electronics Engineering by Zeeshan
1 answer 32 views

A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is?

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 15 views

Total numbers of ascending runs in the sequence 4 6 7 2 9 1 2 8 9 3 0  (1) 3 (2) 5 (3) 7 (4) 9  

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 17 views

A synchronous motor operates at 0.8 pf lagging. If the field current of the motor is continuously increased  1. The power factor decreases upto a certain value of field current and thereafter it increases.  2. The armature current increases upto a certain value of field current and thereafter it decreases.  3. The power factor increases upto a certain value ... field current and thereafter it, increases.  From these, the correct answer is (a) 1, 2 (b) 3, 4 (c) 1, 3 (d) 2, 4

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

For a 1.8o, 2-phase bipolar stepper motor, the stepping rate is 100 steps/second. The rotational speed of the motor in rpm is  (A) 15 (B) 30 (C) 60 (D) 90

asked May 17, 2018 in Electrical Machine by Shimroz123
0 answers 16 views

A commutator with a diameter of 50 cm rotates at 1000 r.p.m. If brush width is 1.5 cm, the time of commutation will be (a) 0.168 m sec (b) 0.374 m sec (c) 0.481 m sec (d) 0.573 m sec

asked May 25, 2018 in Electrical Machine by Shimroz123
1 answer 23 views

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 17 views

DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-300 A, what shunt resistance need to be connected?  A) 0.025 Ω B) 0.05 Ω C) 0.015 Ω D) 0.03 Ω

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A neodymium magnet is a permanent magnet made from an alloy of _________ A) Neodymium and iron B) Neodymium, iron and iodine C) Neodymium and boron D) Neodymium, iron and boron

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

If the load current and flux of a DC motor are held constant, and voltage applied across its armature is increased by 10%, its speed will:  (A) Decrease by 10%. (B) Remain unchanged. (C) Increase by 10%. (D) Increase by 20%. 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 5 views

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 18 views

As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit?

asked Mar 20, 2018 in Electrical Machine by Shimroz123
1 answer 118 views

A cube of material of side 1 cm has a resistance of 0.002 ohm between its opposite faces. If the same volume of the material has a length of 8 cm and a uniform cross-section, the resistance of this length will be 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

DC series motor should never be started at no-load. Justify. 

asked Sep 18, 2018 by Shimroz123
0 answers 536 views

Why dc series motor should not be started at no load?

asked Mar 15, 2018 in Electrical Engineering by Quiz
1 answer 29 views

An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is (A) 5.06 kW (B) 0.3 kW (C) 100 kW (D) 83.33 kW

asked Apr 28, 2018 in Electrical Machine by Shimroz123
0 answers 8 views

A separately excited dc generator is running at rated speed and at no load. If its field winding is suddenly connected to a dc source then rise in armature generated voltage is governed by (1) Armature time constant (2) Field time constant (3) Both (a) and (b) (4) Mechanical time constant

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 26 views

A 200 V dc motor takes a field current of 2 A to generate a back emf of 180 V. If the field winding resistance is 80 Ω, the resistance of the shunt field regulator is (A) 10 Ω (B) 20 Ω (C) 100 Ω (D) 180 Ω

asked Jun 4, 2018 in Electrical Machine by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...