Can you help by answering this question?

What is a shell?

20 views
in Power electronics converters by
A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is 

(A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is 68.73 A

Related questions

1 answer 15 views

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 18 views

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input displacement factor (IDF) and the input power factor (IPF) of the converter will be  (A) IDF IPF = = 0.867; 0.828 (B) IDF IPF = = 0.867; 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 16 views

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be  (A) 31% and 6.8 A (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 18 views

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 14 views

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A. If the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 21 views

A single phase fully controlled thyristor bridge ac -dc converter is operating at a firing angle of 25 degree and an overlap angle 10 degree with constant dc output current of 20A. The fundamental power factor (displacement factor) at input ac mains is : (A) 0.78 (B) 0.827 (C) 0.866 (0) 0.9

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

asked May 18, 2018 in Power Electronics by Shimroz123
1 answer 18 views

A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode.  (A) because the converter inherently does not provide for free-wheeling (B) because the converter does not provide for free-wheeling for high ... the AC supply (D) or else if a gate pulse to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR.

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 24 views

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

asked Apr 28, 2018 in Power Electronics by Shimroz123
1 answer 41 views

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 21 views

a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the secondary side. The P.I.V per thyristor is   (A) 100V (B)141.4V (C)200V (D)282.8V

asked May 17, 2018 in Power electronics converters by Shimroz123
1 answer 6 views

A freewheeling diode in a phase controlled converter  A) Deceases the possibility of discontinuous conduction in the load B) Increases the possibility of discontinuous conduction in the load C) Reduces the power factor and causes over voltages D) Causes over voltages

asked May 20, 2018 in Power electronics converters by Shimroz123
1 answer 48 views

The output voltage waveform of a three-phase square-wave inverter contains  (A) only even harmonics (B) both odd and even harmonic (C) only odd harmonics (D) only triple harmonics

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 13 views

 A single phase full -wave half controlled bridge converter feeds an inductive load: The two SCRs in the converter are connected to a common DC bus. The converter has to have a free wheeling diode (A) Because the converter inherently does not provide for free wheeling (B) Because the converter does not provide for free wheeling for high ... the AC supply (D) Or else if a gate pulse to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 62 views

The corona loss of a 3-phase transmission line is 100 kW at 60 kV/phase and 25 kW at 50 kV/phase. The disruptive critical voltage is (A) 40 kV (B) 43.6 kV (C) 49.6 kV (D) 50 kV

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in the figure. The Dc machine is energized first and the machines rotate at 1 600 1pm. Subsequently the induction machine is also connected to a 50 Hz, three phase source, the phase sequence being consistent with the direction of rotation. In steady state

asked May 20, 2018 in DC machine by Shimroz123
1 answer 38 views

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

asked Apr 28, 2018 in Power Electronics by Shimroz123
0 answers 22 views

A three phase diode bridge rectifier is fed from a 400 V rms, 50 Hz, three phase a.c. source. For the purely resistive load, the peak instantaneous output voltage is 

asked May 25, 2018 in Diode by Shimroz123
0 answers 17 views

The starting torque of a V/f controlled inverter-fed 3-phase induction motor operating at 25 Hz as compared with the same motor operating at 50 Hz is (A) more (B) double (C) equal (D) less 

asked Jun 4, 2018 in Electrical Machine by Shimroz123
1 answer 8 views

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

asked May 23, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 11 views

In a dc-ac 3-phase MOSFET bridge inverter circuit, the switches are marked in a sequence as 1, 2, 3 in the top-half and 4, 5, 6 in the bottom half of the bridge. The triggering sequence of switches that gives balanced output voltage is (A) 1, 2, 3, 4, 5, 6 (B) 1, 5, 3, 4, 2, 6 (C) 1, 6, 2, 4, 3, 5 (D) 1, 4, 2, 5, 3, 6

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 44 views

Explain three phase bridge inverter.

asked Feb 19, 2018 in Unit 4 by Quiz
0 answers 38 views

A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
0 answers 17 views

A three phase 50 Hz, 400 kV transmission line is 300 km long. The line inductance is 0.97 mH/km per phase and capacitance is 0.0115 mF/km per phase. Assume a loss less line. Determine the line wavelength (a line phase constant).  (A) 1250 km (B) 6578 km (C) 4990 km (D) 2445 km 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Consider the following statements with regard to inverters 1. Line commutated inverters can function as isolated ac sources 2. Force commutated inverters can provide independent ac voltage with adjustable voltage and frequency 3. Thyrister based inverters do not require additional circuitry for commutation 4. IGBT, PMOSFET based inverters are more reliable, less costly and less complex. The correct statements are A)1,3 B)1,3,4 C) 2,4 D) 1,4

asked May 24, 2018 in Power Electronics by Shimroz123
1 answer 10 views

A three phase 50 Hz line consists of three conductors each of diameter 21 mm, The spacing between the conductors all follows: A - B = 3m, B - C = 5m, C - A = 3.6m If the line operates at 132 k V, the reactive voltampere generatd by the line per km is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 12 views

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

asked Apr 29, 2018 in Power Electronics by Shimroz123
0 answers 24 views

A 750 Hp, 250 V, 1200 r/min DC motor is connected to a 208 V, 3 phase, 60 Hz, line using a 3 phase bridge converter. The full load armature current is 2500 A and the armature resistance is 4 m ohm. Calculate the required firing angle under rated full load conditions.  (A) 45 deg (B) 208 deg (C) 27 deg (D) 32 deg 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

The power input to the rotor of a 400V, 50 Hz 6 pole three phase induction motor is 20kW. The slip is 3%. The frequency of rotor currents is: (A) 1 Hz (B) 1.5 Hz (C) 2 Hz (D) 1 2 Hz

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 34 views

A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is: (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 43 views

Six MOSFETs connected in a bridge configuration (having no other power device) must be operated as a Voltage Source Inverter (VSI) . This statement is  (A) True, because being majority carrier devices MOSFETs are voltage driven. (B) True, because MOSFETs hav inherently anti-parallel diodes (C) False, because it ... both as Current Source Inverter (CSI) or a VSI (D) False, because MOSFETs can be operated as excellent constant current sources in the saturation region.

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 54 views

A 1-phase, 7.46 kW motor is supplied from a 400 V, 50 Hz A.C mains. Its efficiency is 85% and power factor is 0.8 lagging. Calculate the KVA input (1) 9.56 kVA (2) 5.4 Kva (3) 10.97 kVA (4) 8.6 kVA 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 52 views

The corona loss on a particular system at 50 Hz is 1 kw/phase per km. The corona loss on the same system with supply frequency 25 Hz will be?

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 16 views

In three phase 400 volt, 50 Hz supply, the phase to neutral voltage is   (a) 220 Volt (b) 230 Volt (c) 440 Volt (d) 150 Volt  

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 80 views

The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated conditions is 50 A. Neglecting losses and magnetizing current, the approximate locked rotor line current drawn when the motor is connected to a 236 , V 57 Hz supply is  (A) 58.5 A (B) 45.0 A (C) 42.7 A (D) 55.6 A

asked May 17, 2018 in Electrical Machine by Shimroz123
1 answer 29 views

A 3 phase, 400 volts, 50 Hz, 100 kW, 4 pole squirrel cage induction motor with a rated slip of 2% will have a rotor speed of: (A) 1500 rpm (B) 1470 rpm (C) 1530 rpm (D) 1570 rpm

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 137 views

A 3-phase, 11 kv, 50 Hz, 200 kW load has a power factor of 0.8 lag. A delta connected 3-phase capacitor is used to improve the power factor to unity. The capacitance perphase of the capacitor in micro-farads is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 38 views

The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

asked May 1, 2018 in Electrical Machine by Shimroz123
1 answer 17 views

A 50 kW dc shunt is loaded to draw rated armature current at any given speed. When driven  (i) at half the rated speed by armature voltage control and (ii) at 1.5 times the rated speed by field control, the respective output powers delivered by the motor are approximately. (A) 25 kW in (i) and 75 kW in (ii) (B) 25 kW in (i) and 50 kW in (ii) (C) 50 kW in (i) and 75 kW in (ii) (D) 50 kW in (i) and 50 kW in (ii)

asked May 17, 2018 in DC machine by Shimroz123
0 answers 24 views

A thyristor power converter is said to be in discontinuous when:  (A) The load current is zero even though the load voltage is present. (B) Both load voltage and load current are zero simultaneously. (C) The load current is present even though load voltage is zero. (D) When load current is ripple free. 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 57 views

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) inversely proportional to α and Φ (C) directly proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 21 views

In which type of AC to DC converter efficiency is higher :

asked May 15, 2018 in Power electronics converters by Shimroz123
0 answers 18 views

Three single phase transformers are connected in delta-delta to step down a line voltage of 138 kV to 4160 V to supply power to a production plant. The plant draws 21 MW at a lagging power factor of 86 %. Calculate the apparent power furnished by the HV line.  (A) 24.4 MVA (B) 48.8 MVA (C) 12.2 MVA (D) 6.1 MVA 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor is   (A) square wave (B) triangular wave (C) step function (D) pulsed wave

asked May 17, 2018 in Power electronics converters by Shimroz123
0 answers 15 views

A balanced three phase star connected load is supplied from a three phase 400V 50 Hz supply. The resistance for per phase is 10 Ohm. Find the value of phase current, line current, power factor and total power consumed.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 33 views

A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be (A) 23.06 kW (B) 24.11 kW (C) 25.01 kW (D) 26.21 kW

asked May 17, 2018 in Electrical Machine by Shimroz123
1 answer 14 views

A 4-pole induction motor, supplied by a slightly unbalanced three-phase 50 Hz source, is rotating at 1440 rpm. The electrical frequency in Hz of the induced negative sequence current in the rotor is  (A) 100 (B) 98 (C) 52 (D) 48

asked May 17, 2018 in Induction Machine by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

133 comments

3,086 users

...