19 views
in Bipolar Junction Transistor by
A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region (OFF state) or in the saturation region (ON state). In the ON state, for the BJT 

(A) both the base-emitter and base-collector junctions are reverse biased (B) the base-emitter junction is reverse biased, and the base-collector junction is forward biased (C) the base-emitter junction is forward biased, and the base-collector junction is reverse biased (D) both the base-emitter and base-collector junctions are forward biased

2 Answers

0 votes
by

A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region (OFF state) or in the saturation region (ON state). In the ON state, for the BJT both the base-emitter and base-collector junctions are forward biased

0 votes
by

A BJT is as a power control switch by biasing it in cut-off region (OFF state) or in the saturation region (ON state). In  ON state, for BJT both the base-emitter and base- collector junctions are forward biased

Related questions

1 answer 15 views

In a BJT circuit a pnp transistor is replaced by npn transistor. To analyse the new circuit (1) All calculations done earlier have to be repeated (2) Replace all calculated voltages by reverse values (3) Replace all calculated currents by reverse values (4) Replace all calculated voltages and currents by reverse values 

asked May 28, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 9 views

In a junction transistor, the doping level of collector region is:  (1) Higher than emitter region (2) Lower than base region (3) Is higher than base region but lower than emitter region  (4) Independent of the doping of base and emitter regions.

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
2 answers 17 views

For the active mode BJT operation (A) Emitter Base Junction is Forward Biased and Collector Base Junction is Forward Biased (B) Emitter Base Junction is Reverse Biased and Collector Base Junction is Reverse Biased (C) Emitter Base Junction is Forward Biased and Collector Base Junction is Reverse Biased (D) Emitter Base Junction is Reverse Biased and Collector Base Junction is Forward Biased

asked May 12, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 8 views

Beta cut-off frequency of a transistor is the frequency at which the Beta is • 0.707 of low frequency value • Zero • Equal to low frequency value • None of the above.

asked May 14, 2018 in Electronics Engineering by Shimroz123
1 answer 52 views

As compared to power MOSFET, a BJT has  (a) Lower switching losses but higher conduction losses (b) Higher switching losses and higher conduction losses (c) Higher switching losses but lower conduction losses (d) Lower switching losses and lower conduction losses. 

asked May 13, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 5 views

Cut-off frequency in a resonating circuit is also called as : (A) Full power frequency (B) Half power frequency (C) Resonant frequency (D) Corner frequency

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

In BJT circuits, bulk of the gain is provided by (A) CE configuration (B) CB configuration (C) CC configuration (D) It is not certain

asked May 12, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 21 views

How can BJT be used as an amplifier?

asked Mar 19, 2018 in Bipolar Junction Transistor by Zeeshan
1 answer 18 views

A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

asked May 23, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this waveguide is  (a) 3.57 GHz (b) 3.75 GHz (c) 3.70 MHz (d) 3.57 MHz

asked May 15, 2018 in Electronics communication by Shimroz123
0 answers 15 views

The upper cut off frequency of a capacitive coupled RC amplifier is decided by  A) Input Coupling capacitance B) Transistor internal capacitances C) Output coupling capacitance D) Bypass capacitance

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 27 views

What is the correct sequence of the following step in the fabrication of a monolithic, bipolar junction transistor? 1. Emitter diffusion 2. Base diffusion 3. Buried layer formation 4. Epi–layer formation Select the correct answer using the codes given below (1) 3, 4, 1, 2 (2) 4, 3, 1, 2 (3) 3, 4, 2, 1 (4) 4, 3, 2, 1 

asked May 28, 2018 in Electronics Engineering by Shimroz123
0 answers 79 views

As the wave frequency approaches to cut-off frequency of wave guide, the correct statement is : a. The phase velocity of waves tends to zero. b. The phase velocity of waves tends to velocity of light. c. The phase velocity of waves tends to infinite. d. None of these.

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 31 views

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 120 views

In a bipolar transistor when in saturation, the dc current gain is (a) less than (3 (b) greater than (3 (c) equal to 13 (d) zero

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

Why transistor is called as bipolar device.

asked Sep 4, 2018 by Shimroz123
0 answers 22 views

Maximum junction temperature and maximum ambient temperature of a power transistor (in degree Centigrade) are 150 and 52. The set level power dissipation is 32 watts, transistor thermal factor is 0.7 and of mica washer is 0.5.Thermal resistivity of heat sink (in degree C/W) is  A) 1.8 B) 3.2 C) 6.4 D) 9.8

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 13 views

In a transistor biasing circuit with voltage divider bias circuit, if the operating point is on the left on the load line. (a) peak of the input voltage is clipped. (b) one side peak of the output voltage is clipped. (c) both positive and negative peaks are clipped. (d) there will be a distortion in the middle.

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 32 views

What do you mean by biasing of a transistor?

asked Mar 22, 2018 in Transistor Biasing by Quiz
2 answers 17 views

In BJT, the common emitter gain β is (A) desired to have large value (B) desired to have small value (C) desired to have moderate value (D) the value need not be controlled

asked May 12, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 42 views

A BJT’s voltage stand-off capability when the base current is zero (A) collector-emitter breakdown voltage (B) minimum collector-emitter voltage (C) collector-base breakdown voltage (D) emitter-base voltage

asked Jun 4, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 57 views

Describe transistor as a switch with neat sketch.

asked Jul 10 in Elements of Electronics by Shimroz123
1 answer 69 views

Describe transistor as a switch with neat circuit diagram.

asked Sep 5, 2018 by Shimroz123
1 answer 78 views

 If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

asked Jun 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 14 views

The region consisting of holes and electrons near the p-n junction of a diode is (A) diffusion region (B) neutral zone (C) recombination region (D) depletion region 

asked Jun 4, 2018 in Diode by Shimroz123
1 answer 17 views

A differentiator is not usually used in control system, because it : - (A) reduces damping  (B) increases error  (C) reduces gain margin  (D) increases input noise

asked Apr 30, 2018 in Control System by Shimroz123
1 answer 62 views

In order to switch-off and EHV circuit for maintenance, the following sequence is adopted: (1) Open the circuit breaker, open the isolator, operate the earth switch (2) Operate the earth switch, open the isolator, open the circuit breaker (3) Open the isolator, operate the earth switch, open the circuit breaker (4) Open the isolator, open the circuit breaker, operate the earth switch 

asked May 29, 2018 in Electrical Engineering by Shimroz123
0 answers 31 views

What is a BJT amplifier?

asked Mar 19, 2018 in Bipolar Junction Transistor by Zeeshan
1 answer 14 views

A low-pass filter with a cut-off frequency of 30 Hz is cascaded with a high pass filter with a cut-off frequency of 20 Hz. The resultant system of filters will function as  (A) an all – pass filter (B) an all – stop filter (C) an band stop (band-reject) filter (D) a band – pass filter

asked May 18, 2018 in Analog electronics circuits by Shimroz123
1 answer 14 views

The values of L and C for a low pass filter with cut off frequency of 2.5 KHz and operating with a terminated load resistance of 450 Ohm are given by  (a) 57.3 mH; 0.283 μF (b) 28.66 μH; 0.14 μF (c) 114.64 mH; 0.566 mF (d) 50.23 mH; 0.632 mF

asked May 16, 2018 in Electronics Engineering by Shimroz123
1 answer 49 views

The switch in the circuit has been closed for a long time. It is opened at t = 0. At t = 0+, the current through the 1 micro farad capacitor is A) 0A B) 1A C) 1.25A D) 5A

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 63 views

What is the difference between BJT and FET?

asked Mar 19, 2018 in Bipolar Junction Transistor by Zeeshan
1 answer 28 views

ln HRC fuse the time between cut-off and final current zero is called

asked Apr 26, 2018 in Switchgear And Protection by Shimroz123
0 answers 21 views

Why biasing is required for a transistor?

asked Mar 10, 2018 in Electronics Engineering by Quiz
1 answer 14 views

The 'h' parameter equivalent circuit of a junction transistor is valid for   (A) High frequency, large signal operation (B) High frequency, small signal operation (C) Low frequency, large signal operation.

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 10 views

Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail. 

asked Jul 10 in Elements of Electronics by Shimroz123
0 answers 14 views

Each time you turn the power switch on which control files the computer will check  (1) command.com, io.sys (2) command.com, date.com, time.com (3) command.com, io.sys, msdos.sys (4) chkdsk.exe

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 47 views

Is BJT unipolar or bipolar Why?

asked Jan 5, 2018 in Electronics Engineering by Quiz
1 answer 18 views

Which of the following statements is wrong for transistor biasing methods:  1. The base resistor method does not provide stabilization of operating point 2. The biasing with feedback resistor provides only some stabilization 3. Base resistor method provides better stabilization than collector feedback method 4.Voltage divider bias is widely used because it has stable operating point

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 12 views

Earth coverage dish antenna is used in satellite system. It is characterized by the fact that  (a) It is a narrow beam antenna (b) It is Parabolic antenna (c) it is sharply focused within a small area of the surface of the earth (d) it is a wide angle antenna which covers a large area of the surface of the earth

asked May 15, 2018 in Electronics communication by Shimroz123
1 answer 14 views

What is an emitter follower BJT circuit ? (A) Common Collector Amplifier (B) Common Emitter Amplifier (C) Common Base Amplifier (D) None of the above

asked May 12, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 90 views

In pneumatic control systems the control valve used as final control element converts 

asked Mar 27, 2018 in Control System by Shimroz123
0 answers 67 views

If one of the control springs of PMMC ammeter is broken when it is connected in a circuit, the meter will read  A) Half the correct value of current B) Twice the correct value of current C) An indefinite figure D) Zero

asked Apr 9, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...