14 views
in Network Analysis by
Two incandescent light bulbs of 40 Wand 60 W rating are connected in series across the mains, then . 

A) The bulbs together consume 100 W B) The bulbs together consume 50 W C) The 60 W bulb glows brighter D) The 40 W bulb glows brighter

1 Answer

0 votes
by

Two incandescent light bulbs of 40 Wand 60 W rating are connected in series across the mains, then . The bulbs together consume 50 W 

Related questions

1 answer 28 views

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: A) 195 volt B) 220 volt C) 245 volt D) 440 volt

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

Three 60 W bulbs are in parallel across the 230 V power line. If one bulb burns out

asked May 14, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 33 views

Two heaters, rated at 1000 W, 250 V each are connected in series across a 250 V, 50 Hz ac mains. The total power drawn from the supply would be __________ watt.

asked Mar 31, 2018 in Control System by Shimroz123
0 answers 440 views

A 220 V, 200 W bulb and a 220 V, 100 W bulb are connected in series across a 220 V supply, the power consumed by them will be (a) 33.3 W (b) 66.6 W (c) 100 W (d) 300 W

asked May 25, 2018 in Electrical Engineering by Shimroz123
0 answers 121 views

Two heater wires of equal length are connected first in series and then in parallel. The ratio of heat generated from series to parallel connection will be (a) 4 : 1 (b) 2 : 1 (c) 1 : 2 (d) 1 : 4

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 48 views

Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

asked Mar 25, 2018 in Basic concepts by Shimroz123
0 answers 22 views

In a series RLC circuit, the rms value of voltage across the resistor is 30 V, across the inductor is 60 V and across the capacitor is 20 V. The rms supply voltage would be (A) 110 V (B) 10 V (C) 220 V (D) 50 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

When two transformer of different kVA rating are connected in parallel they share the load in proportion to their respective kVA rating only when their:

asked May 22, 2018 in Transformer by Shimroz123
0 answers 23 views

A diode D, resistor R and inductor L and a switch S are connected in series.When a voltage V is applied across the circuit and switch is put on, the voltage across L changes as  A) V(1-exp(-t R/L)) B) Vexp(-t R/L) C) Ldi/dt +Ri D) V(1-t R/L)

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 91 views

Two bulbs of 500 W and 200 W rated at 250 V will have resistance ratio as?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 22 views

Four identical resistors are first connected in parallel and then in series. The resultant resistance of the first combination to the second will be

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

Three identical resistors are first connected in parallel and then in series. The resultant resistance of the first combination to the second will be?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 28 views

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 29 views

Two condensers of capacity 2F and 3F are connected in Series and a third condenser of 1F is connected in parallel to them. The resultant capacity will 

asked Mar 29, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 61 views

In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

asked May 1, 2018 in Network Analysis by Shimroz123
1 answer 19 views

Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 13 views

In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is (A) 70 V (B) 50 V (C) 60 V (D) 100 V

asked May 12, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

A battery of 40 V and three capacitors of 1000 μF, 500 μF and 100 μF are all connected in (I) parallel and (II) series. The ratio of total charge stored in case I to that in case II is approximately  (a) 3 : 64 (b) 64 : 3 (c) 160 : 3 (d) 104 : 5

asked May 15, 2018 in Battery by Shimroz123
1 answer 32 views

The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density. When frequency is increased to 50 Hz., eddy current loss is :  (A) 256 W (B) 320 W (C) 500 W (D) 625 W

asked Apr 30, 2018 in Switchgear And Protection by Shimroz123
2 answers 27 views

Three lamps are connected in parallel across a 120 Volt source. If one lamp burns out, the remaining two will be: A. Glow dimmer B. Glow brighter C. Not light D. Glow with the same brightness as before

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 6 views

Two two-port networks are connected in cascade. The combination is to be represented as a single two-port network. The parameters of the network are obtained by multiplying the individual a. z-parameter matrix b. h-parameter matrix c. y-parameter matrix d. ABCD-parameter matrix

asked May 24, 2018 in Network Analysis by Shimroz123
1 answer 15 views

In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor  A) Is always zero B) Can never be greater than the input voltage C) Can be greater than the input voltage, however, it is 90° out of phase with the input voltage D) Can be greater than the input voltage, and is in phase with the input voltage

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 41 views

At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

When four resistances of 2W 1W; 5W 2W; 10W 5W and 15W 10 W are connected in parallel, the greatest power is absorbed by • 2 W, 1 W • 5 W, 2 W • 10 W, 5W • 15 W, 10 W

asked May 13, 2018 in Electrical Engineering by Shimroz123
0 answers 58 views

Two d.c. series motors connected in series are driving a mechanical load. If the motors are connected in parallel to drive the same load, the speed becomes  (a) slightly less than double (b) slightly less than half (c) slightly more than double (d) slightly more than half 

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Two resistance 100Ω ± 5Ω ± 15Ω are connected in series. If the errors are specified as standard deviations, the resultant error will be

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
1 answer 34 views

Two coils connected in series have resistance of 600 ohm and 300 ohm and temperature coefficients of 0.1% and 0.4% respectively.The resistance of the combination at 50oC will be 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

One 200 V, 100 W bulb is connected in series with primary of a 200 V, 10 kVA transformer. If its secondary is kept open circuited, then the bulb would have (1) Full brightness (2) Poor brightness (3) A little less than full brightness (4) More than full brightness 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

As a network contains only independent current sources and resistors then if the values of all resistors are doubled then the values of the node voltages are   (A) will become half (B) will remain unchanged (C) will become double (D) cannot be determined unless the circuit configuration and the values of the resistors are known.

asked May 17, 2018 in Network Analysis by Shimroz123
1 answer 28 views

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 21 views

A power station supplies the peak load of 60 Mw, 40 MW and 70 MW to three localities. The annual load factor is 0.50 p.u. and the diversity factor of the load at the station is 1.55. The maximum demand on the station and average load respectively will be 

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 14 views

In an RLC series AC circuit, if frequency is below the resonant frequency, then (a) XC = XL (b) XC < XL (c) XC > XL (d) None of these 

asked May 25, 2018 in Network Analysis by Shimroz123
1 answer 5 views

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 52 views

A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is

asked May 8, 2018 in Electric Power Transmission by Shimroz123
0 answers 13 views

An R-L series AC circuit has R = 10 ohm and XL = 10 ohm. It is connected to an AC voltage source, the phase angle between voltage and current is (a) 30° (b) 45° (c) 60° (d) 36.8°

asked May 25, 2018 in Network Analysis by Shimroz123
1 answer 16 views

Two resistors are said to be connected in series when?

asked Mar 25, 2018 in Basic concepts by Shimroz123
0 answers 189 views

Calculate the power loss, if power generated by two plants are P1=50 MW and P2 =40 MW and the loss coefficients are B11=0.001, B22=0.0025 and B12=-0.0005.  (A) 4.5 MW (B) 5.5 MW (C) 6.5 MW (D) 8.5 MW

asked Apr 5, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...