21 views
in Electronics Engineering by
Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to: 

(1) 1 (2) 0.5

(3) 0.75 (4) 0.33

2 Answers

0 votes
by

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to: 0.5

0 votes
by
Ripple in output current of step down Chopper feeding a RLE load is maximum, when duty cycle is equal to 0.5

Related questions

1 answer 27 views

In dc choppers per unit ripple is maximum when duty cycle is   (a) 0.2 (b) 0.5 (c) 0.7 (d) 0.9

asked May 13, 2018 in Power Electronics by Shimroz123
0 answers 90 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
0 answers 20 views

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5 

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 15 views

A chopper operating at a fixed frequency is feeding an R-L load. As they duty ratio of the chopper is increased from 25% to 75%, the ripple in the load current.

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 7 views

A pulse waveform has a high time of 8 ms and a pulse width of 32 ms. The duty - cycle is equal to: A. 25% B. 50% C. 1% D. 100%

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

The ripple content of load current of a converter feeding RL load is decided by  A) Load resistance alone B) Load inductance alone C) Both load resistance and load inductance D) Neither resistance nor inductance

asked May 20, 2018 in Power electronics converters by Shimroz123
1 answer 48 views

A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:  (1) Zero (2) Infinity (3) L/R (4) R/L 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is  (a) First (b) Second (c) Third (d) Fourth

asked May 15, 2018 in Power Electronic Controlled Drives by Shimroz123
0 answers 23 views

The output voltage of a battery drops from 100 V with zero load current to 80 V when load current is 2 A. The internal resistance of the battery is (a) 10 Ω (b) 20 Ω (c) 40 Ω (d) 50 Ω

asked May 25, 2018 in Battery by Shimroz123
1 answer 11 views

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 16 views

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be  (A) 31% and 6.8 A (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 13 views

In a three-phase system, when the loads are perfectly balanced, the value of neutral current is equal to: A. Zero B. One-third of the maximum value C. Two -third of the maximum value D. The maximum value

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

Three single phase transformers are connected in delta-delta to step down a line voltage of 138 kV to 4160 V to supply power to a production plant. The plant draws 21 MW at a lagging power factor of 86 %. Calculate the apparent power furnished by the HV line.  (A) 24.4 MVA (B) 48.8 MVA (C) 12.2 MVA (D) 6.1 MVA 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 593 views

In a step-up or step-down transformer, electrical power is transferred from one circuit to another without change in

asked May 14, 2018 in Transformer by Shimroz123
1 answer 21 views

"Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with?

asked Mar 25, 2018 in Network Analysis by Shimroz123
0 answers 21 views

In a JFET drain current is maximum when VGS is  (a) zero (b) negative (c) positive (d) equal to Vp

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 13 views

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 8 views

Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency is (a) 2.65 MHz (b) 6.25 MHz (c) 5.26 MHz (d) 6.52 MHz 

asked May 26, 2018 in Electronics Engineering by Shimroz123
1 answer 39 views

A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would  (1) increase progressively  (2) decrease progressively  (3) decrease to a minimum value at α = 0.5 and then increase  (4) increase to a maximum value at α = 0.5 and then decrease

asked Apr 30, 2018 in Power Electronics by Shimroz123
1 answer 17 views

When a source is delivering maximum power to a load, the efficiency of the circuit is always (a) 50% (b) 75% (c) 100% (d) Depends on the circuit parameters

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 26 views

A generator is connected through a 20 MVA, 13.8/138 kV step down transformer, to a transmission line. At the receiving end of the line a load is supplied through a step down transformer of 10 MVA, 138/69 kV rating. A 0.72 pu. load, evaluated on load side transformer ratings as base values , is supplied from the above system. For system base values of 10 MVA and 69 kV in load circuit, the value of the load (in per unit) in generator will be (A) 36 (B) 1.44 (C) 0.72 (D) 0.18

asked May 25, 2018 in Power system by Shimroz123
1 answer 7 views

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 41 views

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 12 views

When the load on a transmission line is equal to the surge impedance loading  (a) The receiving end voltage is less than the sending end voltage  (b) The sending end voltage is less than the receiving end voltage  (c) The receiving end voltage is more than the sending end voltage  (d) The receiving end voltage equal to the sending end voltage 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The initial response when the output is not equal to input is called?

asked Mar 27, 2018 in Control System by Shimroz123
1 answer 25 views

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 18 views

A synchronous generator is feeding a zero power factor (lagging) load at rated current. The armature reaction is  (A) magnetizing (B) demagnetizing (C) cross-magnetizing (D) ineffective

asked May 17, 2018 in Synchronous machine by Shimroz123
1 answer 16 views

If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is?

asked Mar 27, 2018 in Control System by Shimroz123
1 answer 36 views

Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

The threshold effect in demodulators is a) The rapid fall of output SNR when the input SNR falls below a particular value b) Exhibited by all the demodulators when the input SNR is low c) Exhibited by all AM suppressed carrier coherent demodulators d) Exhibited by correlation receivers

asked Jun 15, 2018 in Electronics Engineering by Shimroz123
0 answers 21 views

A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to a 120 V, 60 Hz source. From a wattmeter test, it is known that iron losses are equal to 180 W. Calculate the reactive power absorbed by the core.  (A) 600 var (B) 572 var (C) 180 var (D) 360 var 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

The emf induced in a coil is 1 volt when current in it changes from 0 to 100 mA in time 10mS. Its inductance (in mH) value is  A) 10 B) 50 C) 100 D) 1000

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 14 views

Maximum power is transferred when load impedance is  A) equal to source impedance B) equal to half of the source impedance C) equal to zero D) none of the above

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

The frequency stability of the oscillator output is maximum in _____.   (a) Crystal oscillator (b) Phase shift oscillator (c) LC oscillator (d) Wien bridge oscillator 

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 29 views

If eight -tenths coulomb passes a point in 4 s, the value of current is equal to: A. 1.6 A B. 16 A C. 2 A D. 0.2 A

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

D.C. motor is to a drive a load which is almost nil for certain part of the load cycle and peak value for short duration. We will select the?

asked Mar 20, 2018 in DC motor by Shimroz123
1 answer 14 views

A 1100 kVA, 11 kV/1.1 kV conventional two-winding transformer is connected as a 12.1 kV/11 kV step-down auto-transformer. The rating of the auto-transformer is (A) 1000 kVA (B) 1100 kVA (C) 11000 kVA (D) 12100 kVA

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

asked May 18, 2018 in Power Electronics by Shimroz123
2 answers 38 views

The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

asked Apr 30, 2018 in Switchgear And Protection by Shimroz123
0 answers 24 views

An alternator is feeding an infinite bus bar. Its prime mover is suddenly shut down. The alternator will:  (A) Continue to work as alternator but the direction of rotation will reverse. (B) Come to stand still. (C) Continue to work as synchronous motor and direction of rotation will also be same. (D) Will work as an induction motor.

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

asked May 22, 2018 in Electrical Engineering by Shimroz123
0 answers 41 views

If an energy meter disc makes 10 revolutions in 100 seconds when a load of 450W is connected to it, the meter constant in revolutions per kWh is  A) 1000 B) 500 C) 1600 D) 800

asked Apr 9, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...