Engineering
Login
Register
Search
Ask a Question
Install App
Number of comparators required for an 8 bit flash ADC is:
Number of comparators required for an 8 bit flash ADC is:
(1) 8 (2) 16
(3) 255 (4) 256
asked
May 22, 2018
in
Digital Instrumentation
by
QuestionAnswer
Please
log in
or
register
to add a comment.
← Prev Question
Next Question →
Please
log in
or
register
to answer this question.
1 Answer
0
like
0
dislike
Number of comparators required for an 8 bit flash ADC is:
255
answered
May 22, 2018
by
QuestionAnswer
Please
log in
or
register
to add a comment.
Related questions
The number of comparators required in a 4 bit comparator type ADC is
The number of comparators required in a 3-bit comparator type analog to digital converter is
For an ADC, full scale output voltage is about 10 V.For a resolution of about 9.78mV, number of bits required is ...
In 8 bit successive approximation ADC, clock frequency is 1MHz and reference voltage is 10 V.Conversion time...
For an 8 bit DAC, reference voltage is 10 V. If input to DAC starting from MSB is 10111100, output (in volts) is ...
In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of
In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB
An eight bit digital data 10101100 is fed to an ADC. The reference voltage is +10V. The analog output voltage ...
The number of loop equations required to completely analysing a network comprising of 8 independent
An 1.8° step, 4 -phase stepper motor has 40 teeth on 8 poles of the stator. The number of rotor teeth for...
The percent resolution of an 8 -bit D/A converter is
The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the
An 8 bit converter type A/D converter makes at least 8000conversions/sec. The clock frequency used is
A flash type ADC uses ....
Flash or Parallel ADC
Number of control lines required for 16 to 1 multiplexer is
Which is the fastest type of ADC?
The kVA rating required for a transformer that must handle a maximum load current of 8 A with a ...
If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.
Assuming 8 bits for data, 1 bit for parity, I start bit and 2 stop bits, ...
A 12-bit ADC is operating with a lus clock period and total conversion time is seen to be 14us always....
Compare various electrically erasable memory technique. Also explain flash memory.
The ADC having highest conversion speed is
Which type of ADC gives high resolution?
Write short note on ADC-Amplifier Interface.
Describe the various blocks and their functions in pipelined ADC architecture.
Integrating or Dual Slope ADC
The intel 8086 microprocessor is a _______ processor A. 8 bit B. 16 bit C. 32 bit D. 4 bit
List any four features of 8 bit ISA bus.
The minimum number of wattmeter(s) required to measure 3-phase, 3-wire balanced or unbalanced power is
Minimum number of bits required to represent maximum value of given analogue signal with 0.1% accuracy is:
If the Disk head is located initially at 32, find the number of disk moves required with FCFS if the disk queue...
The minimum number of NAND gates required to implement a XOR gate is ...
Explain the basic operation of an oscilloscope with necessary diagram for each section in detail.
In an induction motor high rotor resistance is required for
What is the required connection for an enhancement type N-MOSFET to function as a resistor?
Why starter is required for starting an induction motor?
An alternator is delivering rated current at rated voltage and 0.8 power-factor lagging. For delivering rated...
A four bit number is given as 0110. Its 2’s complement is
An industrial consumer hall a daily load pattern of 2000 KW, 0.8 lag for...
Initially the number decimal 8 is stored. If instruction RAL is executed twice, the final number stored will be:
Find out the number of address lines required to access 4 KB of RAM
Find out number of data lines required to interface 16 LEDs arrange in the 4 x 4 matrix form.
The minimum number of wattmeter(s) required to measure 3-phase, 4-wire balanced or unbalanced power
How many minimum number of NOR gates are required to realize a two-input X-OR gate?
The number of insulator discs (each rated 11 kV) required in a suspension type insulator string
A network has 10 nodes and 17 branches. The number of independent mesh equations required to solve the
The number of poles of 8/6 stepper motor can be :
What is essential for a successive approximation Nbit ADC?
A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the...