# Power-factor of industrial arc and induction furnace is:

126 views
Power-factor of industrial arc and induction furnace is:

Power-factor of industrial arc and induction furnace is: very low lagging

## Related questions

Explain with neat diagram construction and working of Ajax Wyatt vertical core induction furnace.

Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  (C) Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

Differentiate between core type and core less induction furnace.

What are the industrial application of electrolysis?

The type of single-phase induction motor having the highest power factor at full load is (A) shaded pole type (B) split-phase type (C) capacitor-start type (D) capacitor-run type

Power factor of running induction motor is better when (1) Running at half load (2) Full load (3) ¾ of load (4) None of the above

At which time power factor of the induction motor is low?

For arc welding current range is usually  (1) 10 to 15 A (2) 30 to 40 A (3) 50 to 100 A (4) 100 to 350 A

The arc voltage in a circuit breaker is :

The supply for arc welding is :

At an industrial sub-station with a 4 MW load, a capacitor of 2 MVAR is installed to maintain the load power factor at 0.97 lagging. If the capacitor goes out of service, the load power factor becomes (A) 0.85 (B) 1.00 (C) 0.80 lag (D) 0.90 lag

The power factor of an induction motor under no load conditions will be close to (A) 0.2 lagging (B) 0.2 leading (C) 0.5 lagging (D) Unity

A synchronous motor has better power factor as compared to that of an equivalent induction motor. This is mainly because?

A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be (A) 23.06 kW (B) 24.11 kW (C) 25.01 kW (D) 26.21 kW

How rating of main switch and cable is selected for Industrial Installation.

State any two applications of each for the following types of electrical heating : (i) Direct resistance heating(ii) Indirect induction heating (iii) Direct.arc heating (iv) Dielectric heating

The measurement of dielectric loss and power factor is done using  (A) Weins Bridge (B) Hays Bridge (C) Schering Bridge (D) Wheat Stone Bridge

The commonly used gases in tungsten arc welding are 1.Hydrogen and oxygen 2.Hydrogen and organ 3.Hydrogen and helium 4.Helium and argon

Arc resistance  (1) increases with increase in arc current (2) decrease with increase in arc current (3) is independent of arc current (4) is independent of arc length

For heating a magnetic material using induction heating, the hysteresis and eddy current losses are respectively proportional to (a) f and f 2 (b) f 2 and f (c) f and f (d) none of the above

The rotor power output of a 3 -phase induction motor is 15 kW and the corresponding slip is 4%. The rotor copper losses will be: (A) 600 W (B) 625 W (C) 650 W (D) 700 W

For induction heating, which of the following is abnormally high?  A)Voltage B) Current C) Frequency D) Phase angle

The range of frequencies used in induction heating is :  (A) 0-25 Hz  (C) less than 200 Hz  (B) 50 to 100 Hz  (D) more than 1 kHz

State the working principle and operation of Automatic power factor controller used in Transmission and Distribution system.

What will be the efficiency when the transformer operates at unity power factor and 60% of full load

A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is  (A) 86.7% (B) 88.26% (C) 88.9% (D) 87.8%

Measurement of power and power factor of a 3-phase system by two wattmeter method can be obtained in case of  1. Balanced load and balanced source  2. Balanced source with 3-phase 3-wire unbalanced load  3. Unbalanced source with 3-phase 3-wire balanced load  4. Balanced source with 3-phase 4-wire unbalanced load  5. unbalanced and unbalanced source    (a) 1 only (b) 2, 3 and 5 (c) 1, 2, 3, 4 and 5 (d) 1, 2, 3 and 5

The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are (A) 0.5 pu, 0.866 pu (B) 0.866 pu, 0.5 pu (C) 0.707 pu, 0.707 pu (D) 0.5 pu, 0.5 pu

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

A three-phase synchronous motor connected to ac mains is running at full load and unity power factor. lf its shaft load is reduced by half and field current is held constant then its new power factor will be

When alternator excitation increases and machine is operating at lagging power factor then (A) Armature current increases (B) Armature current decreases (C) Armature current remains unchanged (D) Armature voltage remains unchanged

A 1-phase, 7.46 kW motor is supplied from a 400 V, 50 Hz A.C mains. Its efficiency is 85% and power factor is 0.8 lagging. Calculate the KVA input (1) 9.56 kVA (2) 5.4 Kva (3) 10.97 kVA (4) 8.6 kVA

An alternator is delivering rated current at rated voltage and 0.8 power-factor lagging. For delivering rated current at rated voltage and 0.8 poWer—factor leading, the required excitation will be:  (A) less  (B) more (C) more or less (D) the same

The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

Draw and explain power flow diagram of induction motor.

Draw power and control circuit for simple plugging of induction motor.

Is induction heating safe?

The electrode of a direct are furnace is made of (1) Tungsten (2) Graphite (3) Silver (4) Copper

Write the purpose of coal and ash handling unit. Also write different activities that arc carried out in this unit.

Compare industrial electrical installation and residential electrical installation.

State and explain "power factor tariff'.

Draw and explain bulk correction method for power factor & control.