Can you help by answering this question?

Explain power relations in three phase circuit.

20 views
in Electric Power Transmission by
Why are shunt reactors connected at the receiving end of long transmission line system:

(1) To increase the terminal voltage

(2) To compensate voltage rise caused by capacitive charging at light load

(3) To improve power factor

(4) None of these

1 Answer

0 votes
by

Why are shunt reactors connected at the receiving end of long transmission line system: To compensate voltage rise caused by capacitive charging at light load

Related questions

0 answers 23 views

In long AC transmission lines, the receiving end voltage becomes greater than sending end voltage at light load or no load operation. This is due to (a) Ferranti effect (b) Skin effect (c) Proximity effect (d) Corona effect 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 24 views

The sending and receiving end voltages of a three phase transmission line at 100 MW load are equal at 230 KV. The phase line impedance is j14 ohm. Calculate the maximum steady state power that can be transmitted over the line.  (A) 3778.5 MW (B) 2234.56 MW (C) 1784.19 MW (D) 512.37 MW

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

A synchronous condenser is used at the receiving end of a transmission line for (A) supplying lagging kVA (B) voltage control (C) frequency control (D) maintaining a higher voltage than at the sending end 

asked Jun 4, 2018 in Power system by Shimroz123
2 answers 95 views

The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

asked Apr 28, 2018 in Power system by Shimroz123
0 answers 26 views

Which of the following relations is true for long transmission line ? (a) VS = AVR – BIR (b) VS = BVR + AIR (c) VS = AVR + BIR (d) VS = BVR – AIR

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 26 views

To increase power transfer capability of a long transmission line, we should:  (1) Increase line resistance (2) Increase transmission voltage (3) Decrease line reactance (4) Both (2) & (3)

asked May 22, 2018 in Electric Power Transmission by Shimroz123
2 answers 48 views

A long transmission line has considerable ……………….. effect. A) series capacitance B) shunt capacitance C) series inductance D) shunt inductance

asked Jun 4, 2018 in Electric Power Transmission by Shimroz123
1 answer 42 views

A 100 km long transmission line is loaded at 110 kV.if the loss of line is 5 MW and the load is 150 MVA, the resistance of the line is?

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 32 views

In an AC transmission line difference in phase of voltage at two ends of the line is due to (a) System voltage (b) Insulators (c) Resistance of line (d) Reactance of line

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 31 views

A voltage of 1000 kV is applied to an overhead line with its receiving end open. If the surge impedance of the line is 500 ohm, then the total surge power in the line ill

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 27 views

For a short line if the receiving end voltage is equal to the sending end voltage under loaded conditions: a) the sending end power factor is unity b) the receiving -end power factor is unity c) the sending-end power factor is leading d) the receiving end power factor is leading

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 79 views

how the booster is connected in transmission line ?

asked Aug 18, 2017 in Electric Power Transmission by Zeeshan
0 answers 16 views

The bundled conductor in EHV transmission line system provides (a) increased inductance (b) reduced capacitance (c) increased capacitance (d) increased voltage gradient

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 380 views

The main consideration for operating transmission line at high voltage is (a) to increase efficiency only. (b) to reduce power loss only. (c) to increase power transmission capability only. (d) All of the above

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 189 views

A 10 km long line has a characteristic impedance of 400 ohms. If line length is 100 km, the characteristic impedance is: (1) 4000 Ω (2) 400 Ω (3) 40 Ω (4) 4 Ω

asked May 28, 2018 in Electric Power Transmission by Shimroz123
1 answer 391 views

In which of the following transmission lines, the value of the Shunt admittance should be approximated to zero ? (A) A 66 kV 35 km long line (B) A 132 kV 200 km long line (C) A 220 kV 300 km long line (D) A 400 kV 500 km long line

asked May 8, 2018 in Electric Power Transmission by Shimroz123
0 answers 45 views
1 answer 30 views

For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic impedance is: (1) 100 Ω (2) 50 Ω (3) 25 Ω (4) 10 Ω

asked May 29, 2018 in Electric Power Transmission by Shimroz123
1 answer 115 views

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line 

asked May 8, 2018 in Electric Power Transmission by Shimroz123
0 answers 25 views

Which of the following is used for power factor improvement in transmission line ? (a) Three phase induction (b) An overexcited three phase synchronous motor running on no load (c) Three phase AC series motor (d) Choke

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 21 views

If diameter of each conductor of a transmission line is ‘d’, then the diameter of n-layer stranded conductor will be (a) (2n – 1) d (b) (2n + 1) d (c) (3n – 1) d (d) (3n + 1) d 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 91 views

The presence of earth in case of overhead transmission line (a) increases capacitance (b) increases inductance (c) decreases capacitance (d) decreases inductance

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 22 views

An overhead transmission line has a span of 260 m. The weight of the conductor is 0.68 kg/m. The maximum allowable tension in the line is 1550 kg. Maximum sag of the line should be (a) 5.8 m (b) 4.6 m (c) 2.7 m (d) 3.7 m 

asked May 25, 2018 in Electric Power Transmission by Shimroz123
1 answer 12 views

The input impedance of a short circuited loss less transmission line of characteristic impedance 50 Ohm is

asked May 23, 2018 in Electric Power Transmission by Shimroz123
1 answer 20 views

What type of insulator will be used if the direction of the transmission line is to be changed?

asked May 22, 2018 in Electric Power Transmission by Shimroz123
1 answer 40 views

The inductance of single phase two wire power transmission line per km gets doubled when the  (a) Distance between wires is doubled  (b) Distance between the wires is increased four fold  (c) Distance between the wires is increased as square of the original distance  (d) Radius of the wire is doubled

asked May 13, 2018 in Electric Power Transmission by Shimroz123
1 answer 27 views

The inductance of a power transmission line increases with (A) decrease in line length. (B) increase in conductor diameter. (C) increase in spacing between phase conductors. (D) increase in load current carried by conductors.

asked May 13, 2018 in Electric Power Transmission by Shimroz123
0 answers 52 views

A 220 kV, 3 phase transmission line is 60 km long. The resistance is 0.15 ohm / km and the inductance is 1.4 mH / km. Use the short line model to find the power at the sending end when the line is supplying a three phase load of 300 MVA at 0.8 pf lagging at 220 kV.  (A) 5.58MW (B) 80MW (C) 85.58MW (D) 74.42 MW 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

A three phase 50 Hz, 400 kV transmission line is 300 km long. The line inductance is 0.97 mH/km per phase and capacitance is 0.0115 mF/km per phase. Assume a loss less line. Determine the line wavelength (a line phase constant).  (A) 1250 km (B) 6578 km (C) 4990 km (D) 2445 km 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

The time taken for a surge to travel a 600 km long overhead transmission line is?

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 40 views

Effect of increase in temperature in an overhead transmission line is (a) to increase stress and length both (b) to decrease stress and length both (c) to decrease stress and increase length (d) None of the above 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 30 views

Stability of a transmission line can be increased by

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 89 views

A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

asked May 3, 2018 in Electric Power Transmission by Shimroz123
0 answers 75 views

Determine the transformer tap ratios when the receiving end voltage is equal to the sending end voltage, the high voltage line operates at 220 kV and transmit 80 MW at 0.8 pf and the impedance of the line is (40+j140)ohm. Assume tstr=1.0  (A) 0.8 (B) 0.9 (C) 0.7 (D) 0.6 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

The power loss in a transmission line depends on (a) current in the line. (b) resistance of the line. (c) length of the line. (d) All of the above 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 19 views

A transmission line to be reciprocal, the condition is (a) A = D (b) AC – BD = 1 (c) AD – BC = 1 (d) AB – CD = 1  

asked May 25, 2018 in Electric Power Transmission by Shimroz123
1 answer 25 views

Earth wire on EHV overhead transmission line is provided to protect the line against:

asked May 22, 2018 in Electric Power Transmission by Shimroz123
1 answer 16 views

The conductor of a 10 km long, single phase, two wire line are separated by a distance of 1.5 m. The diameter of each conductor is 1 cm, If the conductors are of copper, the inductance of the circuit is

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 22 views

In large capacity transformers, 5% of the turns at the end of hv winding are provided with extra insulation so as to provide protection  (1) against corona (2) against lightning (3) due to surges occurring during switching operation (4) All of these

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 44 views

why we use aluminium conductor and not copper in transmission lines ?

asked Aug 18, 2017 in Electric Power Transmission by Zeeshan
1 answer 17 views

A long overhead transmission line is terminated by its characteristic impedance. Under this operating condition, the ratio of the voltage to the current at different points along the line will?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 41 views

what is mean by long transmission line ?

asked Aug 18, 2017 in Electrical Engineering by Zeeshan
1 answer 45 views
1 answer 13 views

A quarter wave line open circuited at far end behaves as:  (1) Inductance (2) L and C in parallel (3) Capacitance (4) L and C in series

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 46 views

A single-line-to-ground fault on a overhead transmission line creates (A) voltage sag (B) voltage swell (C) over voltage (D) voltage flicker 

asked Jun 4, 2018 in Electric Power Transmission by Shimroz123
1 answer 80 views

Galloping in transmission line conductors arises generally due to - (A) asymmetrical layer of ice formation (B) vortex phenomenon in light winds (C) heavy weight of line conductors (D) adoption of horizontal conductor

asked May 13, 2018 in Electric Power Transmission by Shimroz123
1 answer 55 views

How many insulator disc used for 33 kV transmission voltage line?

asked Dec 5, 2017 in Electric Power Transmission by Quiz

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...