Can you help by answering this question?

Cost of low voltage capacitor /kVAr is

13 views
in Alternator by
If the excitation of an alternator operating in parallel with other alternators decreased, its:

(1) Power factor becomes more leading

(2) Output Kw will change

(3) Power factor becomes more lagging

(4) Power factor becomes unity

1 Answer

–1 vote
by

If the excitation of an alternator operating in parallel with other alternators decreased, its: Power factor becomes more leading

Related questions

1 answer 23 views

While keeping the excitation constant, if the steam supply of an alternator running in parallel with another identical alternator is increased, then (A) It would over-run the other alternator (B) Its rotor will fall back in phase with respect to the other machine (C) Its portion of share in load will increase (D) Its power factor would be decreased.

asked Apr 28, 2018 in Electrical Machine by Shimroz123
0 answers 29 views

When two alternators A and B are operating in parallel, the increase in steam supply to alternator A will cause the active power output of (1) Alternator A to be decreased and alternator B to be increased (2) Alternators A and B is not affected (3) Alternators A and B is increased (4) Alternator A to be increased and alternator B to be decreased

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 39 views

 In an alternator if the winding is short pitched by 60 electrical degrees, its pitch factor will be: A) 1.0 B) 0.866 C) 0.75 D) 0.50

asked Jun 4, 2018 in Alternator by Shimroz123
1 answer 40 views

A field excitation of 20 A in a certain alternator results in an armature current of 400 A in short circuit and a terminal voltage of 2000 V on open circuit. The magnitude of the internal voltage drop within the machine at a load current of 200 A is  (A) 1 V (B) 10 V (C) 100 V (D) 1000 V

asked May 17, 2018 in Alternator by Shimroz123
1 answer 11 views

When two alternators are operating in parallel, the cause for circulating current is (A) increase in the excitation of one machine (B) increase in the driving torque of one machine (C) reduction in angular velocity of one machine (D) identical speed/load characteristics of both machines

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A synchronous motor is delivering 80% of its rated output and is operating at UPF. If its excitation is increased, then  (1) the output delivered gets increased (2) its pf becomes lagging (3) the output delivered gets decreased (4) its pf becomes leading

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

In a superconductor, if the temperature is decreased below its critical temperature, the value of critical magnetic field will (a) Increase (b) Decrease (c) Not change (d) Increase or decrease depending on the superconductor material

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 64 views

The magnitude of various voltage drops that occur in an alternator depends on?

asked Mar 18, 2018 in Alternator by Shimroz123
1 answer 44 views

In an alternator at lagging power factor the generated voltage per phase as compared to that at unity power factor?

asked Mar 18, 2018 in Alternator by Shimroz123
0 answers 8 views

 When alternator excitation increases and machine is operating at lagging power factor then (A) Armature current increases (B) Armature current decreases (C) Armature current remains unchanged (D) Armature voltage remains unchanged

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

The power factor of an alternator depends on?

asked Mar 18, 2018 in Alternator by Shimroz123
1 answer 51 views

A 8 pole alternator rotates at 750 r.p.m. Its frequency is

asked May 15, 2018 in Alternator by Shimroz123
1 answer 23 views

Two 3-phase, Y-connected alternators are to be paralleled to a set of common busbars. The armature has a per phase synchronous reactance of 1.7 Ohm and negligible armature resistance. The line voltage of the first machine is adjusted to 3300 V and that of the second machine is adjusted to 3200 V. The machine voltages are in phase at the ... are paralleled. Under this condition, the synchronizing current per phase will be  (A) 16.98 A (B) 29.41 A (C) 33.96 A (D) 58.82 A

asked May 17, 2018 in Alternator by Shimroz123
1 answer 19 views

Which rotor is use for high speed in turbo alternators?

asked Mar 18, 2018 in Alternator by Shimroz123
0 answers 16 views

the division of active power amongst alternators running in parallel depends upon (1) speed-load characteristics of prime mover (2) V-I characteristics of alternator (3) Excitation voltages of alternators (4) Both (b) and (c) 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

In a synchronous generator if the excitation increased from a low value to normal value, with a fixed load  (A) The armature current increases and the power factor decreases  (B) The armature current decreases and the power factor also decreases  (C) The armature current decreases and the power factor increases but is lagging  (D) The armature current decreases and the power factor increases and is leading

asked Apr 29, 2018 in Electrical Machine by Shimroz123
0 answers 18 views

The torque produced in a 4-pole machine is 100 Nm. If machine is re-wound with 6 ploes, other things remaining the unchanged, then the torque produced would be (1) 66.67 Nm (2) 100 Nm (3) 150 Nm (4) 133.33 Nm 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

If load on a d.c. shunt motor is increased, its speed is decreased due primarily to?

asked Mar 26, 2018 in DC motor by Shimroz123
1 answer 34 views

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 42 views

 An 8-pole alternator runs at 750 rpm and supplies power to a 6-pole induction motor which has a full load slip of 3 percent. The full load speed of the induction motor will be: A) 1000 rpm B) 920 rpm C) 950 rpm D) 970 rpm

asked Jun 4, 2018 in Alternator by Shimroz123
1 answer 91 views

An alternator has a phase sequence of RYB for its phase voltage. In case the direction of rotation of alternator is reversed, the phase sequence will become?

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 19 views

If frequency is decreased 4 times, then skin depth of an Electromagnetic wave inside a conductor will be :  A) halved B) quadrupled C) doubled D) no change

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 31 views

In alternator where the voltage drop occurs?

asked Mar 18, 2018 in Alternator by Shimroz123
1 answer 20 views

A coil of wire is placed in a changing magnetic field. If the number of turns in the coil is decreased, the voltage induced across the coil will: A. increase B. decrease C. remain constant D. be excessive

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

In a parallel plate capacitor of capacitance Co, the electric field is E. If a dielectric slab with dielectric constant = 7 is introduced to fill capacitor completely, the electric field will become (a) 7E (b) E/7 (c) E/3.5 (d) E. Co 

asked May 25, 2018 in Capacitor by Shimroz123
1 answer 16 views

A 100 turn coil has an inductance of 6 mH. If the number of turns is increased to 200, all other quantities remaining the same, the inductance will be:

asked May 22, 2018 in Inductance by Shimroz123
0 answers 13 views

In a transistor biasing circuit with voltage divider bias circuit, if the operating point is on the left on the load line. (a) peak of the input voltage is clipped. (b) one side peak of the output voltage is clipped. (c) both positive and negative peaks are clipped. (d) there will be a distortion in the middle.

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

Is the speed of alternator is directly proportional to frequency?

asked Mar 18, 2018 in Alternator by Shimroz123
1 answer 14 views

Drop in alternator frequency is corrected by: (1) Damper winding (2) Increased prime mover output (3) Automatic voltage regulator (4) None of these

asked May 22, 2018 in Alternator by Shimroz123
0 answers 22 views

If two 3-phase transformers with unequal voltage ratios are connected in parallel, the result is (A) circulating current on no-load (B) no circulating current on no-load (C) dead short-circuit (D) equal no-load secondary emfs 

asked Jun 4, 2018 in Electrical Machine by Shimroz123
2 answers 76 views

 With three resistances connected in parallel, if each dissipates 20 W the total power supplied by the voltage source equals?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 41 views

In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

asked May 1, 2018 in Electrical Machine by Shimroz123
1 answer 13 views

A transmission line is operating with a Phase shift of 80° between two ends. If the load is suddenly increased A) The phase displacement will increase B) The phase displacement will decrease C) The phase displacement will not change D) The surge impedance will increase

asked May 24, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

A 3-phase induction motor is running at slip ‘s’. If its two supply leads are interchanged, then the operating slip at that instant will be:

asked May 22, 2018 in Induction Machine by Shimroz123
1 answer 23 views

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

asked Apr 28, 2018 in Electrical Machine by Shimroz123
0 answers 25 views

Which alternator will have more number of poles ? (a) coupled to steam turbine (b) coupled to gas turbine (c) coupled to hydraulic turbine (d) None of the above 

asked May 26, 2018 in Alternator by Shimroz123
0 answers 24 views

An alternator is feeding an infinite bus bar. Its prime mover is suddenly shut down. The alternator will:  (A) Continue to work as alternator but the direction of rotation will reverse. (B) Come to stand still. (C) Continue to work as synchronous motor and direction of rotation will also be same. (D) Will work as an induction motor.

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 52 views

 The driving power from the prime-mover driving the alternator is lost but the alternator remains connected to the supply network; the field supply also remains on. The alternator will: A) get burnt B) behave as an induction motor but will rotate in the opposite direction C) behave as a synchronous motor and will rotate in the same direction D) behave as a synchronous motor but will rotate in a reverse direction to that corresponding to generator action 

asked Jun 4, 2018 in Alternator by Shimroz123
0 answers 20 views

One 200 V, 100 W bulb is connected in series with primary of a 200 V, 10 kVA transformer. If its secondary is kept open circuited, then the bulb would have (1) Full brightness (2) Poor brightness (3) A little less than full brightness (4) More than full brightness 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

If the contents of an accumulator are Ex-ORed with itself and placed in the accumulator itself, then  A) Carry flag will be set B) The accumulator contains all 1’s C) The zero flag is set D) The accumulator contents are shifted left by one bit

asked May 20, 2018 in Digital Electronics by Shimroz123
1 answer 23 views

Two 550 kVA alternator operate in parallel to supply the following loads I. 250 KW at 0.95 p.f. lagging II. 100 KW at 0.85 p.f. leading One machine is supplying 200 KW at 0.9 p.f. lagging. The p.f. of other machine must be

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

The voltage regulation for 0.95 lead pf is zero for an alternator. If so, the voltage regulation for 0.9 lead pf with all other conditions remaining same will be (A) Positive (B) Negative (C) Zero (D) Insufficient data

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

An alternator is connected to a bus. For a symmetrical fault at the bus, the fault level is 60 MVA. If another alternator is connected to the same bus, the new fault level will be (1) 120 MVA (2) 60 MVA (3) 30 MVA (4) 15 MVA 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

An alternator with frequency f1 is to be synchronized with an infinite bus of frequency f. For proper synchronization (1) f1=f (2) f1<f (3)f1>f (4) either (b) or (c) 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

Two transformers operating in parallel will share the load depending upon their

asked May 12, 2018 in Transformer by Shimroz123
1 answer 40 views

A 60 Hz, 2 pole alternator should run at • a. 3000 r.p.m. c. 1500 r.p.m. • b. 3600 r.p.m. d. 1800 r.p.m.

asked May 14, 2018 in Alternator by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...