Can you help by answering this question?

Which of the following elements is not bilateral ?

18 views
in Electrical Engineering by
A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

1 Answer

0 votes
by

A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is 2.94 GHz

Related questions

1 answer 14 views

A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this waveguide is  (a) 3.57 GHz (b) 3.75 GHz (c) 3.70 MHz (d) 3.57 MHz

asked May 15, 2018 in Electronics communication by Shimroz123
1 answer 31 views

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

The values of L and C for a low pass filter with cut off frequency of 2.5 KHz and operating with a terminated load resistance of 450 Ohm are given by  (a) 57.3 mH; 0.283 μF (b) 28.66 μH; 0.14 μF (c) 114.64 mH; 0.566 mF (d) 50.23 mH; 0.632 mF

asked May 16, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

In a circular waveguide the dominant mode is:  (1) TE01 (2) TE11 (3) TE20 (4) TE21

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 12 views

The dominant mode in a rectangular wave guide is TEo, because this mode has  a. No attenuation  b. No cut off   c. No magnetic field component  d. The highest cut—off wavelength

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 15 views

The upper cut off frequency of a capacitive coupled RC amplifier is decided by  A) Input Coupling capacitance B) Transistor internal capacitances C) Output coupling capacitance D) Bypass capacitance

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

The dominant mode in cylindrical waveguide

asked May 23, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Beta cut-off frequency of a transistor is the frequency at which the Beta is • 0.707 of low frequency value • Zero • Equal to low frequency value • None of the above.

asked May 14, 2018 in Electronics Engineering by Shimroz123
0 answers 5 views

Cut-off frequency in a resonating circuit is also called as : (A) Full power frequency (B) Half power frequency (C) Resonant frequency (D) Corner frequency

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

Which of the following sorts is quickest when sorting the following set: 1 2 3 5 4  (1) Quick Sort (2) Bubble Sort (3) Merge Sort (4) Heap Sort 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 16 views

A commutator with a diameter of 50 cm rotates at 1000 r.p.m. If brush width is 1.5 cm, the time of commutation will be (a) 0.168 m sec (b) 0.374 m sec (c) 0.481 m sec (d) 0.573 m sec

asked May 25, 2018 in Electrical Machine by Shimroz123
1 answer 14 views

A low-pass filter with a cut-off frequency of 30 Hz is cascaded with a high pass filter with a cut-off frequency of 20 Hz. The resultant system of filters will function as  (A) an all – pass filter (B) an all – stop filter (C) an band stop (band-reject) filter (D) a band – pass filter

asked May 18, 2018 in Analog electronics circuits by Shimroz123
1 answer 15 views

A two conductor 1 - pi line operates at 50 Hz.The diameter of each conductor is 4 cm and are spaced 6 m apart. What is the capacitive susceptance to neutral per km?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 8 views

State the function of following components related to mimic diagram. 1) PL 2) OPL 3) CHL 4) GCK 5) LTK 6) ARK

asked Sep 2, 2018 by Shimroz123
0 answers 15 views

Total numbers of ascending runs in the sequence 4 6 7 2 9 1 2 8 9 3 0  (1) 3 (2) 5 (3) 7 (4) 9  

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 79 views

As the wave frequency approaches to cut-off frequency of wave guide, the correct statement is : a. The phase velocity of waves tends to zero. b. The phase velocity of waves tends to velocity of light. c. The phase velocity of waves tends to infinite. d. None of these.

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 19 views

If frequency is decreased 4 times, then skin depth of an Electromagnetic wave inside a conductor will be :  A) halved B) quadrupled C) doubled D) no change

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 11 views

A two conductor 1 - pi line operates at 50 Hz. The diameter of each conductor is 2 cm and are spaced 3m apart. What is the line to line capacitance ?

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 49 views

A high-pass filter has a resistance R = 2 kΩ The lowest input frequency to be passed is 7.5 kHz. The value of suitable coupling capacitor must be: A) 0.001 pico Farad B) 0.01 pico Farad C) 0.1 pico Farad D) 1 pico Farad

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
2 answers 19 views

A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region (OFF state) or in the saturation region (ON state). In the ON state, for the BJT  (A) both the base-emitter and base-collector junctions are reverse biased (B) the base-emitter junction is reverse ... (C) the base-emitter junction is forward biased, and the base-collector junction is reverse biased (D) both the base-emitter and base-collector junctions are forward biased

asked May 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

The EM wave which does not propagate through a rectangular waveguide with a=30 mm & b=15 mm is : a. EM wave of frequency 4.5 GHz b. EM wave of frequency 5.5 GHz c. EM wave of frequency 50 GHz d. EM wave of frequency 300 GHz

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 59 views

A Lissajous pattern on an oscilloscope has 5 horizontal tangencies and 2 vertical tangencies. The frequency of the horizontal input is 1000 Hz. What is the frequency of the vertical input?  (A) 400 Hz (B) 5000 Hz (C) 4000 Hz (D) 2500 Hz

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 41 views

A 0.5 Hp, 6 pole wound rotor induction motor is excited by a 3 phase 60 Hz source. Calculate the frequency of the rotor current at standstill.  (A) 50 Hz (B) 30 Hz (C) 60 Hz (D) 120 Hz 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Low pass filter with cut off frequency of 100 kHz and high pass filter with cut off frequency of 50 kHz are connected in tandem, the resultant filter is • Low pass filter with cut off frequency of 100 kHz • High pass filter with cut off frequency of 50 kHz • Band pass filter with pass band from 50 kHz to 100 kHz. • None of the above.

asked May 14, 2018 in Electronics Engineering by Shimroz123
0 answers 24 views

What is the energy stored in the magnetic field at a solenoid of 40 cm long and 4 cm diameter wound with 100 turns of wire carrying a current at 20A?  (A) 0.705 Joule (B) 0.789 Joule (C) 0.587 Joule (D) 0.658 Joule 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A rectangular magnet of magnetic moment M is cut into two piece of same length, the magnetic moment of each piece will be

asked Mar 29, 2018 in Electrical engineering materials by Shimroz123
0 answers 44 views

The connected load of a consumer is 2 kW and his maximum demand is 1.5 kW. The load factor of the consumer is (a) 0.375 (b) 0.75 (c) 1.33 (d) None of these  

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 135 views

In a pure capacitive circuit if the supply frequency is reduced to 1/2, the current will?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 47 views

In a pure inductive circuit if the supply frequency is reduced to 1/2, the current will?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
2 answers 51 views

Define: 1) frequency, 2) cycle, 3) time period, 4) amplitude

asked Aug 8, 2018 by Quiz
1 answer 101 views

The loop transfer of a system is G(s) H(s) = 5/(s+1) (2s+1)(3s+1) which has the phase crossover frequency fc = 0.16 Hz. The gain margin (dB) of the system is  (a) 6 (b) 4 (c) 2 (d) 0

asked May 15, 2018 in Control System by Shimroz123
1 answer 30 views

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
0 answers 43 views

A thyristor is triggered by a pulse train of 5 kHz. The duty ratio is 0.4. If the allowable average power is 100 W, the maximum allowable gate drive power will be 

asked May 25, 2018 in Power Electronics by Shimroz123
1 answer 28 views

The energy used by a 1.5kW heater in 5 minutes is:

asked May 22, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

Consider a cube of material of sides 1 cm with a resistance of 0.003 Ω between its opposite faces. What is the resistance if the same volume of the material is drawn into a length of 50 cm with a uniform cross – section? A) 0.003 Ω B) 0.15 Ω C) 7.5 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

asked Apr 28, 2018 in Electrical Machine by Shimroz123
0 answers 21 views

A material has conductivity of 10–2 mho/m and relative permittivity of 4. The frequency at which the conduction current in the medium is equal to the displacement current, is (a) 450 MHz (b) 900 MHz (c) 45 MHz (d) 90 MHz

asked May 25, 2018 in Physics by Shimroz123
1 answer 22 views

The stator of a 415V, 50 Hz, 4-pole slip ring Induction Motor is excited by rated frequency with slip rings open circuited. The rotor is made to rotate at a speed of 600 rpm in the opposite direction to the normal direction, The frequency of induced voltage across slip ring is A) 30 Hz B) 70 Hz C) 20 Hz D) 35 Hz

asked Jun 17, 2018 in Induction Machine by Shimroz123
1 answer 18 views

The speed of a 4-pole induction motor is controlled by varying the supply frequency while maintaining the ratio of supply voltage to supply frequency (V/f ) constant. At rated frequency of 50 Hz and rated voltage of 400 V its speed is 1440 rpm. Find the speed at 30 Hz, if the load torque is constant  (A) 882 rpm (B) 864 rpm (C) 840 rpm (D) 828 rpm

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 8 views

A 4 bit counter is used to count from 0,1,2...n. Value of “n” is

asked May 14, 2018 in Digital Electronics by Shimroz123
1 answer 26 views

A 3 layer, total diameter of an ACSR conductor is 5 cm. Find the diameter of each strand?

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 21 views

In a graph, the number of independent loops is 6 and the number of independent cut sets is 5, The total number of branches in the graph is A) 9 B) 12 C) 10 D) 11

asked May 24, 2018 in Network Analysis by Shimroz123
1 answer 46 views

In a differential amplifier the differential voltage gain is 500 and the common mode voltage gain is 0.5. The CMRR in dB is (a) 80 (b) 60 (c) 30 (d) 20

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 6 views

When a dominant mode wave guide not terminated in its characteristic impedance is excited with a 10 GHZ signal then if d is the distance between two successive minima of the standing wave in the guide then   (A) d = 1.5 cm (B) d is less then 1.5 cm (C) d is greater then 1.5 cm (D) d = 3 cm

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 46 views

A waveguide termination having VSWR of 1.1 is used to dissipate 100 watts of power. The reflected power will be A) 0.2268 W B) 0.5868 W C) 0.3468 W D) 0.4568 W 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

Consider the following transducers : 1. LVDT 2. Piezoelectric 3. Thermocouple 4. Photovoltaic cell  Which of the above are active transducers ?

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

Consider the following statements with regard to a GTO : 1. The turn-off gain of the GTO is large. 2. Large negative gate current pulses are required to turn off the GTO. 3. GTO has large reverse blocking capability. Which of the above statements is/are correct ? (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 129 views

MSXML is  (1) A Microsoft language (2) XML parser that ships with Internet explorer 5.0 (3) Used for interacting with XML (4) None of these

asked Apr 10, 2018 in Computer Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...