# How many minimum number of NOR gates are required to realize a two-input X-OR gate?

8 views
How many minimum number of NOR gates are required to realize a two-input X-OR gate?

by
5 NOR gates are required to realize a two input X-OR gate.

## Related questions

The minimum number of NAND gates required to implement a XOR gate is  A) 5 B) 4 C) 3 D) 6

In case of a ‘High Voltage DC’ transmission, how many minimum conductors are required?

How many flip-flops are required to build a binary counter circuit to count from 0 to 1023 ? (a) 1 (b) 6 (c) 10 (d) 23

The output of an exclusive–NOR gate is 1. Which input combination is correct? (1) A = 1, B = 0 (2) A = 0, B = 1 (3) A = 0, B = 0 (4) None of these

Which of the following gates can be used to realize all possible combinational logic functions?  (i) OR gate (ii) NOR gate (iii) Exclusive OR gate (iv) NAND gate (v) AND gate  (A) (iii), (iv) and (v)  (B) (i), (iii) and (iv)  (C) (ii) and (iv)  (D) (i) and (v)

The minimum number of wattmeter(s) required to measure 3-phase, 3-wire balanced or unbalanced power is  A) 1 B) 2 C) 3 D) 4

A NOR gate is equivalent to a bubbled AND gate. This statement is an outcome of: (1) De Morgan’s Law (2) Involution Law (3) Law of Absorption (4) Idempotent Law

The o/p of a 2 - input OR gate is 1 when its   1. both inputs are 1 2. both inputs are 0 3.either input is 1 4. either input is 0

How many flip-flops are required to construct a mod-32 counter?  A) 32 B) 6 C) 5 D) 4

In an unclocked R-S flip flop made of NOR gates, the forbidden input condition is:  (1) R=0, S=0 (2) R=1, S=0 (3) R=0, S=1 (4) R=1, S=1

How many bits are required to represent one nibble ?

How many bits are required to encode 32 level PCM:  (1) 6 (2) 5 (3) 4 (4) 3

When A = 0., B = 0, C = 1 then in two input logic gate we get gate  (A) XOR gate (B) AND gate (C) NAND gate (D) NOR gate

For a NAND gate, when one or more inputs are low then the output will be A) Low B) High C) Alternately high and low D) High or low depending on relative magnitude of inputs

Minimum number of bits required to represent maximum value of given analogue signal with 0.1% accuracy is: a. 8 bits b. 9 bits c. 10 bits d. 12 bits

The number of comparators required in a 3-bit comparator type analog to digital converter is  A) 2 B) 3 C) 7 D) 8

Build using minimum number of CMOS gates. Three input NAND gate. Two input NOR gate Three input NOR gate Two input AND gate Two input OR gate

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

Number of control lines required for 16 to 1 multiplexer is

The output of a 2-input NAND gate with high at both the inputs will be • High • Low • High & low • None of the above.

In application of superposition theorem, one is required to solve as many circuits as there are  1. Nodes 2. Branches 3. Meshes 4. Sources

In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of bits required is   (A) 7 (B) 8 (C) 9 (D) 200

The number of comparators required in a 4 bit comparator type ADC is (A) 16 (B) 15 (C) 17 (D) 12

How many time we should half the number n to reach 1.  (1) n (2) log(n) (3) n(log(n)) (4) n2

Two sinusoidal signals having the same amplitude and frequency are applied to the X and Y inputs of a CRO. The observed Lissajous figure is straight line. The phase shift between the two signals would be (1) Zero (2) 90 degrees (3) Either zero or 180 degrees (4) Either 90 degrees or 270 degrees

IC which has quad 2 input AND gates   (A) 7411 (B) 7404 (C)7400 (D) 7408

How much is the potential difference between two points if 0.5 J of energy is required to move 0.4 C of charge between the two points?

The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is (1) 2 sin ωt (2) 2 sin (ωt + 45°) (3) 2 sin (ωt – 45°) (4) 22 sin ωt + 45°)

How many bits are needed to address 64 K memory: - a) 3 b) 10 c) 16 d) 32

what is the minimum voltage required to turn on a diode ?

Draw the symbol, logic expression and truth table of NOR gate.

The average time required to reach a storage location in the memory to read or retrieve the contents of memory is called as A) Turnaround time B) Latency time C) Access time D) Response time

Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is (A) causal & linear (B) non-causal & linear (C) causal & non-linear (D) non-causal & non-linear

The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with its major axis changing orientation slowly and repeatedly. The following inference can be made from this  A) The signals are not sinusoidal ... but not equal C) The signals are sinusoidal with their frequencies very close but not equal D) There is a constant but small phase difference between the signals

A certain appliance uses 350 W. If it is allowed to run continuously for 24 days, how many kilowatt- hours of energy does it consume? A.20.16 kWh B.201.6 kWh C.2.01 kWh D.8.4 kWh

The number of loop equations required to completely analysing a network comprising of 8 independent branches and 6 nodes including the reference node shall be A) 3 B) 2 C) 4 D) 5

A network has 10 nodes and 17 branches. The number of independent mesh equations required to solve the network is   (a) 7 (b) 8 (c) 10 (d) 45

If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19