Can you help by answering this question?

What is the symbol for AC power?

16 views
in Electrical Engineering by
The materials used for permanent magnets should have

1 Answer

0 votes
by

The materials used for permanent magnets should have high retentivity, high coercivity

Related questions

1 answer 278 views

Those materials are well suited for making permanent magnets which have _____ retentivity and _______ coercivity.

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

Hard steel is suitable for making permanent magnets because?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

Soft magnetic materials should have (a) Large saturation magnetization and large permeability (b) Low saturation magnetization and large permeability (c) Large saturation magnetization and low permeability (d) Low saturation magnetization and low permeability

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

In permanent magnets, the desired features are (1) High retentivity, low corecitivity (2) Low retentivity, high corecitivity (3) Low retentivity, low corecitivity (4) High retentivity, high corecitivity

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Permanent magnets are normally made of?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Those magnetic materials are best suited for making armature and transformer cores which have____permeability and_______hystersis loss.

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 8 views

For an SCR with turn-on time of 5 microsecond, an ideal trigger pulse should have   (a) short rise time with pulse width = 3 µsec (b) long rise time with pulse width = 6 µsec (c) short rise time with pulse width = 6 µsec (d) None of the above 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A material for good magnetic memory should have?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

The material used for fuse wire should be of   (a) low resistivity and high melting point (b) high resistivity and high melting point (c) high resistivity and low melting point (d) low resistivity and low melting point 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

_______ is used for heating non -conducting materials.  (1) Eddy current heating (2) Arc heating (3) Induction heating (4) Dielectric heating

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Name the material used for :- (i) Moving coil (ii) Permanent magnet in PMMC instrument.

asked Sep 6, 2018 by Shimroz123
1 answer 24 views

A permanent magnet stepper motor with 8 poles in stator and 6 poles in rotor will have a step angle of (a) 7.5° (b) 15° (c) 30° (d) 60°

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 124 views

A digital board has a unipolar square clock of 250MHz. If the clock on the board at all places should have all the harmonic components which have more than 10 % of DC value, the board has to be designed for at least —  A) 250MHz B) 750MHz C) 1250 MHz D) 2500 MHz

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

Which of the following semiconductor materials is (are) used for manufacturing solar cells?  (1) Gallium arsenide (2) Indium arsenide (3) Cadmium sulfide (4) All of these

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 30 views

Explain the electrical losses of magnetic materials used for the cores of inductors and transformer.

asked Mar 10, 2018 in Power Electronics by Quiz
1 answer 9 views

Two materials have resistance temperature coefficients of 0.004 and 0.0002 respectively at a given temperature. In what ratio should the wires made of these materials be connected in series so as to have an overall temperature coefficient of 0.002?

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
2 answers 13 views
0 answers 8 views

Super conducting materials can be used for (a) ore refining. (b) magnetic levitation in high speed trains. (c) medical resonance imaging. (d) All of the above  

asked May 26, 2018 in Physics by Shimroz123
1 answer 12 views

Insulating materials have the function of?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 19 views

The path of magnetic flux in a transformer should have?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 15 views

When the north poles of two bar magnets are brought close together, there will be: A. no force B. a downward force C. a force of attraction D. a force of repulsion

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

What should be the value of earthing resistance for large power stations?

asked May 29, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

For proper earthing, what should be the maximum value of earth resistance while carrying out the testing of earth continuity path ?   (a) 1 Ω (b) 2 Ω (c) 5 Ω (d) 10 Ω 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

For a class A operation, the biasing resistor should be adjusted such that  (A) Q-point never lies (B) Q-point lies in the middle of the load line (C) Q-point lies in the cut off region (D) Q-point lies on the operating region

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

Magnetic materials used in Hard disc, Floppy disc are (a) NiCo, CuNiFe, Cr02, Fe203 (b) NiCo, CNiFe, Cr02, Fe2O3 (c) NiCu, CuNiFe, Cr02, Fe203 (d) NiCo, CuNiFe, Cr02, Fe202

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 25 views

Materials used in plate earthing are   (a) Wood coal  (b) Salt, earthing plate   (c) (a) and (b) both  (d) None of the above 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

If you used 600 W of power for 60 h, you have used? A.36 kWh B.3.6 kWh C.10 kWh D.1 kWh

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 35 views

A fuse wire should have :  (A) Low specific resistance and high melting point (B) Low specific resistance and low melting point (C) High specific resistance and high melting point (D) High specific resistance and low melting point

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 14 views

An ideal voltage source should have?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 14 views

Which of the following materials is used in the construction of thermistors? A) Pure metal B) Pure semiconductor C) Pure insulator D) Sintered mixture of metal oxides 

asked Jun 17, 2018 in Electronics Engineering by Shimroz123
1 answer 10 views

For an insulating material, dielectric strength and dielectric loss should be respectively   (A) high and high (B) low and high (C) high and low (D) low and low.

asked May 16, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Electric supply for electroplating should be through a

asked May 15, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

A coherent QPSK demodulator is required on ground for receiving data from a LEO satellite. What should be optimum order of PLL in the carrier phase tracking loop?  A) 1st order B) 2nd order C) 3rd order D) None of the above

asked Apr 9, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...