30 views
in Physics by
A cable has an insulation of relative permittivity 2. If the insulation is replaced by one of relative permittivity 4, then capacitance of the cable (a) is doubled (b) is halved (c) remains unchanged (d) is reduced 

Related questions

0 answers 19 views

A material has conductivity of 10–2 mho/m and relative permittivity of 4. The frequency at which the conduction current in the medium is equal to the displacement current, is (a) 450 MHz (b) 900 MHz (c) 45 MHz (d) 90 MHz

asked May 25, 2018 in Physics by Shimroz123
1 answer 37 views

The velocity of travelling wave through a cable of relative permittivity 36 is

asked May 3, 2018 in Physics by Shimroz123
0 answers 107 views

Three materials X, Y and Z having relative permittivity 2.5, 3.0 and 4.0 respectively are used in a single core cable. The materials on inner most and outer most layer respectively should be (a) X and Y (b) Y and Z (c) X and Z (d) Z and X 

asked May 25, 2018 in Physics by Shimroz123
1 answer 60 views

If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance for 50 km length will be

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 17 views

A parallel polarized wave is incident from air into paraffin having relative permittivity 3, the value of its Brewster angle is: (1) 0° (2) 30° (3) 45° (4) 60°

asked May 28, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

The bridge most suited for accurate measurement of relative permittivity of dielectric materials is (A) Carey Foster Bridge (B) Anderson’s bridge (C) Heaviside Bridge modified by Campbell. (D) Schering Bridge.

asked Apr 28, 2018 in Control System by Shimroz123
1 answer 30 views

A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

asked Mar 25, 2018 in Basic concepts by Shimroz123
0 answers 17 views

A megger is to measure insulation resistance of a cable. The cable should be connected to   (a) Battery (b) DC supply (c) AC supply (d) No supply  

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
2 answers 33 views

If an atom loses one or more electrons, it becomes _____.

asked May 29, 2018 in Physics by Shimroz123
1 answer 24 views

A single core lead sheathed cable with two dielectrics of permittivity 4 and 3, respectively, are subjected to same maximum stress. If the conductor diameter is 1.5 cm, the outer diameter of the first dielectric is (A) 1.125 cm (B) 1.5 cm (C ) 2 cm (D) 8 cm

asked Apr 28, 2018 in Power system by Shimroz123
0 answers 14 views

One 200 KVA transformer has an iron loss of 1 KW and full load Cu loss of 2 KW. Its load KVA corresponding to maximum efficiency is:  (A) 100 KVA (B) 141.4 KVA (C) 50 KVA (D) 200 KVA 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 26 views

What is the lowest acceptable insulation resistance for a cable?

asked Mar 10, 2018 in High voltage engineering by Quiz
1 answer 20 views

An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided

asked May 12, 2018 in Control System by Shimroz123
0 answers 90 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
1 answer 12 views

RJ 45 UTP cable has _____cables. A. 2 Pairs B. 3 Pairs C. 4 Pairs D. 5 Pairs

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 17 views

In PCM system, if we increase the quantization levels from 2 to 8, the relative bandwidth requirements will:  (1) Be doubled (2) Remain same (3) Be tripled (4) Becomes eight times

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
3 answers 34 views

A radioactive isotope has a half-life of 10 days. If today there are 125 g of it left, what was its original weight 40 days earlier  (a) 600 g (b) 1000 g (c) 1250 g (d) 2000 g 

asked Apr 9, 2018 in Physics by Shimroz123
1 answer 8 views

In a 3-phase extra-high voltage cable, a metallic screen around each core insulation is provided to  (a) Facilitate heat dissipation (b) Give mechanical strength (c) Obtain longitudinal electric stress (d) Obtain radial electric stress 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

An Oil-filled cable has a working stress of ___________ kV/mm.  (A) 10 (B) 12 (C) 13 (D) 15

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) 1.0 ohm in series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 11 views

An optical fiber cable laid underground has developed a discontinuity at a distance d from the source end. The fault can be located using the instrument  (a) Optical spectrum Analyzer (OSA) (b) Optical Time Domain Reflectometer (OTDR) (c) Optical Power Meter (OPM) (d) Laser Diffractometer (LD)

asked May 15, 2018 in Digital Instrumentation by Shimroz123
0 answers 17 views

The way a card game player arranges his cards as he picks them up one by one, is an example of  (1) Insertion sort (2) Selection sort (3) Bubble sort (4) Merge sort

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 14 views

"Any number of current sources in parallel may be replaced by a single current source whose current is the algebraic sum of individual source currents and source resistance is the parallel combination of individual source resistances". The above statement is associated with?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 15 views

In a BJT circuit a pnp transistor is replaced by npn transistor. To analyse the new circuit (1) All calculations done earlier have to be repeated (2) Replace all calculated voltages by reverse values (3) Replace all calculated currents by reverse values (4) Replace all calculated voltages and currents by reverse values 

asked May 28, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 70 views

The power in a 3-phase load is measured by two watt meters. If one watt meter reads zero, then the load power factor is (A) Zero (B) 0.5 (C ) 0.866 (D) unity 

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 18 views

If a 3-phase, 400V, 50Hz, 4 pole induction motor is running at a slip of 5% then the relative speed of rotor field with respect to stator filed is:

asked May 22, 2018 in Induction Machine by Shimroz123
1 answer 21 views

An 800 kV transmission line has a maximum power transfer capacity of P. If it is operated at 400 kV with the series reactance unchanged, the new maximum power transfer capacity is approximately (A) P (B) 2P (C) P / 2 (D) P / 4

asked May 25, 2018 in Power system by Shimroz123
1 answer 16 views

A 100 turn coil has an inductance of 6 mH. If the number of turns is increased to 200, all other quantities remaining the same, the inductance will be:

asked May 22, 2018 in Inductance by Shimroz123
0 answers 59 views

A Lissajous pattern on an oscilloscope has 5 horizontal tangencies and 2 vertical tangencies. The frequency of the horizontal input is 1000 Hz. What is the frequency of the vertical input?  (A) 400 Hz (B) 5000 Hz (C) 4000 Hz (D) 2500 Hz

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 45 views

The reactance offered by a capacitor to an alternating current of frequency 50 Hz is 10 ohm. If frequency is increased to 100 Hz, the reactance will be (a) 2.5 ohm (b) 5.0 ohm (c) 20.0 ohm (d) 40.0 ohm 

asked May 25, 2018 in Capacitor by Shimroz123
0 answers 13 views

If temperature of a radiating body is 1500 °C, the wavelength at which maximum radiant energy occurs is (a) 2.87 µm (b) 1.63 µm (c) 1.01 µm (d) 20.85 µm 

asked May 25, 2018 in Physics by Shimroz123
1 answer 64 views

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 35 views

What is the frequency of an alternator which has 2 poles and makes 3600 revolutions per minute? A) 3600 HZ B) 60 Hz C) 120 Hz D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 41 views

In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

asked May 1, 2018 in Electrical Machine by Shimroz123
1 answer 25 views

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

asked Mar 20, 2018 in Induction Machine by Shimroz123
0 answers 61 views

An energy meter has a constant of 600 rev/kWh. If the meter makes 10 revolutions in 20 s, what is the load in kW?  (A) 0.75 kW (B) 1.5 kW (C) 3 kW (D) 6 kW 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 59 views

A cable has inductance of 0.22 mH per kilometer and capacitance of 0.202 µF per kilometer. The surge impedance of the cable is (a) 50 Ω (b) 42 Ω (c) 33 Ω (d) 28 Ω

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 30 views

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

asked May 29, 2018 in Amplifier by Shimroz123
0 answers 13 views

The power in a 3phase circuit is measured with the help of 2 wattmeters. The reading of one of wattmeters is positive and that of the others is negative. The magnitude of readings is different. It can be concluded that the power factor of the circuit is  (A) Unity (B) 2 (lagging) (C) 5 (lagging) (D) Less than 0.5 (lagging)

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop gain is (a) 1 (b) 1,00,000 (c) 50 (d) 0.02

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 14 views

If a dynamometer wattmeter is connected in an ac circuit, the power indicated by the wattmeter will be (a) volt-ampere product (b) average power (c) peak power (d) instantaneous power 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 188 views

Peak sidelobe amplitude (relative) of -57 dB is provided by the window function  A) Hamming B) Blackman C) Hanning D) Bartlet

asked Apr 7, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

If temperature of a pure silicon specimen is increased, then (a) only number of free electrons increase. (b) only number of free holes increase. (c) number of free holes and free electrons increases. (d) only number of free holes decrease. 

asked May 25, 2018 in Physics by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...