Ask a Question
A transmission line to be reciprocal, the condition is
A transmission line to be reciprocal, the condition is (a) A = D (b) AC – BD = 1 (c) AD – BC = 1 (d) AB – CD = 1
May 25, 2018
Electric Power Transmission
to add a comment.
← Prev Question
Next Question →
to answer this question.
What type of insulator will be used if the direction of the transmission line is to be changed?
In a transmission line if booster transformers are to be used, preferred location will be
Stability of a transmission line can be increased by
If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.
In an AC transmission line difference in phase of voltage at two ends of the line is due to
Earth wire on EHV overhead transmission line is provided to protect the line against:
A single-line-to-ground fault on a overhead transmission line creates
To increase power transfer capability of a long transmission line, we should:
why there is a difference between the insulation on the beginning and end of transmission line ?
If diameter of each conductor of a transmission line is ‘d’, then the diameter of n-layer stranded conductor
An overhead transmission line has a span of 260 m. The weight of the conductor is 0.68 kg/m. The maximum
The input impedance of a short circuited loss less transmission line of characteristic impedance 50 Ohm is
Galloping in transmission line conductors arises generally due to
The power loss in a transmission line depends on
The inductance of a power transmission line increases with
Which of the following relations is true for long transmission line ?
Which of the following is used for power factor improvement in transmission line ?
The main consideration for operating transmission line at high voltage is
how the booster is connected in transmission line ?
The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.
A long transmission line has considerable ……………….. effect.
For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic
A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of
Effect of increase in temperature in an overhead transmission line is
The bundled conductor in EHV transmission line system provides
The presence of earth in case of overhead transmission line
Why are shunt reactors connected at the receiving end of long transmission line system:
The inductance of single phase two wire power transmission line per km gets doubled when the
If in a short transmission line, resistance and inductance are found to be...
The necessary condition to diagonalise a matrix is that (A) its all Eigen values should be distinct. (B) its Eigen vectors should be independent. (C) its Eigen values should be real. (D) the matrix is non-singular.
One of the necessary and sufficient condition for a network function N(s)=p(s)/q(s) to be a transfer function is...
If R, L and C are the parameters of a resistor then the condition for the resistor to be non-inductive is
A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient?
For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is
How many insulator disc used for 33 kV transmission voltage line?
In which of the following transmission lines, the value of the Shunt admittance should be
In case the height of transmission tower is increased, which of the following parameter is likely to change?
The purpose of guard ring in transmission lines is to
For 11kV line the inductance per km per phase will be of the order of:
For 11 kV line the capacitance per km per phase will be of the order of:
For a two port network to be reciprocal:
The necessary and sufficient condition for a rational function of, T(s) to be driving point impedance of an RC
For a two -port reciprocal network, the three transmission parameters are A = 4, B = 7 and C = 5. ...
A 20-MVA, 6.6-kV, 3-phase alternator is connected to a 3-phase transmission line. The per unit
When the load on a transmission line is equal to the surge impedance loading
A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km
Surge impedance loading (SIL) of power transmission line is the power delivered to a purely
The time taken for a surge to travel a 600 km long overhead transmission line is?
In order to recover the original signal from the Sampled one, what is the condition to be satisfied for sampling ...
If the transmission line is loaded with leading reactive volt amperes, there will be rise of voltage at the...