371 views
in Electrical Measurements and Instrumentation by
Internal resistance of a micro-ammeter is 500 ohm. Shunt resistance required to increase its range from 0-100 µA to 0-10 A will be approximately (a) 0.05 Ω (b) 0.005 Ω (c) 0.5 Ω (d) 5.0 Ω

Related questions

1 answer 12 views

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) 1.0 ohm in series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 23 views

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 11 views

Series resistance required to read 0-250 V with a moving coil instrument of internal resistance 2 ohm and full scale deflection of 50 mA is (a) 49998 Ω (b) 4998 Ω (c) 498 Ω (d) 49.8 Ω

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 20 views

The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. What is the value of series resistor to be used?

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 17 views

DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-300 A, what shunt resistance need to be connected?  A) 0.025 Ω B) 0.05 Ω C) 0.015 Ω D) 0.03 Ω

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 21 views

 The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, what is the value of the shunt resistance to be used?

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 21 views

A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

asked May 22, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 5 views

In order to increase the range of a voltmeter

asked May 15, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 23 views

If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

asked May 23, 2018 in Amplifier by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 24 views

A separately excited dc motor is required to be controlled, from a 3-phase supply, for its operation in the first quadrant only. The most preferred converter would be  (a) 3-phase fully controlled converter (b) 3-phase fully controlled converter with free wheel diode (c) 3-phase dual converter (d) 3-phase half wave converter 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 51 views

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

asked Mar 21, 2018 in DC generator by Shimroz123
1 answer 8 views

The measurement range of an ammeter can be increased by using a:

asked May 22, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 54 views

A moving coli ammeter has a fixed shunt of 0.02 Ω with a coil circuit resistance of R=1 kΩ and needs potential of 0.5 V across it for full scale deflection. Calculate the value of shunt to give full scale deflection when the total current is 10 A. (1) 0.05 Ω (2) 0.005 Ω (3) 0.5 Ω (4) 0.0005 Ω

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

asked May 17, 2018 in Electrical Machine by Shimroz123
1 answer 60 views

If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance for 50 km length will be

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 37 views

If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 36 views

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

asked May 3, 2018 in Electrical Machine by Shimroz123
1 answer 40 views

Two waves have frequency of 500 Hz. One is set at its maximum value whereas the other at zero. The phase angle between them will be

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 13 views

The external characteristic of a shunt generator can be obtained directly from its – characteristic   1. internal 2. open-circuit 3. load-saturation 4. Performance 

asked May 13, 2018 in Electrical Machine by Shimroz123
1 answer 17 views

Two voltmeters have the same range 0-400V. The internal impedance are 30,000 Ohms and 20,000 Ohms. If they are connected in series and 600V be applied across them, the readings are

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 33 views

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter (b) Fully controlled bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

The full scale range of PMMC voltmeter is 100 V and its sensitivity is 1000 Ω/V. If the meter reads 50 V, the current through the voltmeter is (A) 0.05 mA (B) 0.5 mA (C) 5 mA (D) 50 mA 

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 16 views

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 39 views

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

asked May 3, 2018 in Electrical machine design by Shimroz123
1 answer 23 views

Neglecting saturation, if current taken by a series motor is increased from 10 A to 12 A, the percentage increase in its torque is ........ percent

asked Mar 26, 2018 in DC motor by Shimroz123
1 answer 19 views

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 125 views

How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

asked Sep 5, 2018 by Shimroz123
1 answer 28 views

It is desired to convert a 0-1000A meter movement, with an internal resistance of 100 ohms, into a 0-100mA meter. The required value of shunt resistance is about 

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 16 views

500 Bytes of data needs to be transmitted from an UART every lOOms. What should be the minimum transmission baud rate of UART, assuming 1 start bit, 8 data bits and 2 stop bits?  A) 50000 B) 55000 C) 40000 D) 45000

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

asked May 12, 2018 in Electronics communication by Shimroz123
0 answers 31 views

An ammeter of 0-25 A range has a guaranteed accuracy of 1% of full scale reading. The current measured 5 A The limiting error is  A) 2% B) 2.5% C) 4% D) 5%

asked Apr 9, 2018 in Electronics Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...