Can you help by answering this question?

An oscilloscope measures

11 views
in Electrical Measurements and Instrumentation by
Series resistance required to read 0-250 V with a moving coil instrument of internal resistance 2 ohm and full scale deflection of 50 mA is (a) 49998 Ω (b) 4998 Ω (c) 498 Ω (d) 49.8 Ω

Related questions

1 answer 12 views

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) 1.0 ohm in series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 14 views

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

asked May 22, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 20 views

A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect • 10 W resistance in series • 10 W resistance in parallel • 10/1999 W resistance in series • 10/1999 W resistance in parallel

asked May 13, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 18 views

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
0 answers 370 views

Internal resistance of a micro-ammeter is 500 ohm. Shunt resistance required to increase its range from 0-100 µA to 0-10 A will be approximately (a) 0.05 Ω (b) 0.005 Ω (c) 0.5 Ω (d) 5.0 Ω

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 51 views

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 50 views

A moving coli ammeter has a fixed shunt of 0.02 Ω with a coil circuit resistance of R=1 kΩ and needs potential of 0.5 V across it for full scale deflection. Calculate the value of shunt to give full scale deflection when the total current is 10 A. (1) 0.05 Ω (2) 0.005 Ω (3) 0.5 Ω (4) 0.0005 Ω

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 23 views

Five cells, each with an e.m.f. of 2V and internal resistance of 0.5Ω are connected in series. The resulting battery will have

asked May 14, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

 In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is   (A) 1.810% (B) 0.181% (C)12.45% (D) 0.0018%

asked May 17, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 16 views

A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

asked May 22, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 20 views

The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. What is the value of series resistor to be used?

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 23 views

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 22 views

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

asked May 8, 2018 in Electrical Engineering by Shimroz123
0 answers 37 views

A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 14 views

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 28 views

It is desired to convert a 0-1000A meter movement, with an internal resistance of 100 ohms, into a 0-100mA meter. The required value of shunt resistance is about 

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 37 views

If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

asked Mar 21, 2018 in DC generator by Shimroz123
1 answer 32 views

A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 30 views

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
1 answer 200 views

A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 22 views

The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is A. 1,000 V B. 2,000 V C.31.25 V D. 3,125 V

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

A single-phase, 50 kVA, 250 V/500 V two winding transformer has an efficiency of 95% at full load, unity power factor. If it is re-configured as a 500 V/750 V auto-transformer, its efficiency at its new rated load at unity power factor will be  (A) 95.752% (B) 97.851% (C) 98.276% (D) 99.241%

asked May 17, 2018 in Transformer by Shimroz123
0 answers 13 views

 A single phase, 2000V alternator has armature resistance and reactance of 0.8 ohm and 4.94 ohm respectively. The voltage regulation of the alternator at 100A, 0.8 leading pf is (A) 7% (B) - 8.9% (C) - 6.3% (D) 0%

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 91 views

Two bulbs of 500 W and 200 W rated at 250 V will have resistance ratio as?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 39 views

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

asked May 3, 2018 in Electrical machine design by Shimroz123
0 answers 7 views

The deflecting torque of a moving coil instrument depends on (a) supply frequency (c) flux in the coil (b) inverse of area of coil (d) square of the voltage

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is

asked May 8, 2018 in Electrical Machine by Shimroz123
1 answer 16 views

 The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, what is the value of the shunt resistance to be used?

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 13 views

A 6V zener diode is used to provide voltage regulation with a series resistance of 100 Ohms and supply voltage is 12V. When under no load the power dissipated in the zener diode is (a) 60mW (b) 36mW (c) 360mW (d) 3600mW

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...