Can you help by answering this question?

How the electricity is transmitted?

47 views
in Electric Power Transmission by
The connected load of a consumer is 2 kW and his maximum demand is 1.5 kW. The load factor of the consumer is (a) 0.375 (b) 0.75 (c) 1.33 (d) None of these  

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

Related questions

1 answer 117 views

The maximum demand of consumer is 2 kW and his daily energy consumption is 20 units. Its Load Factor is (1) 10.15% (2) 41.6 % (3) 50 % (4) 60% 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

In a power generating station the Demand Factor and Load Factor are 0.5 and 0.2, respectively. If the connected load is 400 MW, the average demand is (A) 40 MW (B) 100 MW (C) 140 MW (D) 280 MW

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

The three non -inductive loads of 5 kW, 3 kW and 2 kW are connected in a star network between R, Y and B phases and neutral. The line voltage is 400 V. The current in the neutral wire is nearly (a) 11 A (b) 14 A (c) 17 A (d) 21 A

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 46 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 20 views

A generating station has a maximum demand of 30 MW, a load factor of 60% and a plant capacity factor of 50%. The reserve capacity of the plant is   (a) 5 MW (b) 4 MW (c) 6 MW (d) 10 MW 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 39 views

A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy generated per annum will be: A) 2.19 x 106 MWhr B) 600 MWhr C) 250 MWhr D) 7.50 x 106 MWhr

asked Jun 17, 2018 in Electric Power Generation by Shimroz123
1 answer 24 views

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

asked May 20, 2018 in Transformer by Shimroz123
1 answer 12 views

A generating st ation has a maximum, demand of 20 mW, load factor of 60%, a plant capacity factor of 50% and a plant Use factor of 72%. What is the reserve capacity of the plant, if the plant, while running as per schedule, were fully loaded?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 18 views

A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor of 45% and if the plant while running as per schedule, were fully loaded. The daily energy produced will be

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 14 views

One 200 KVA transformer has an iron loss of 1 KW and full load Cu loss of 2 KW. Its load KVA corresponding to maximum efficiency is:  (A) 100 KVA (B) 141.4 KVA (C) 50 KVA (D) 200 KVA 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

A consumer finds that after running 10 kVA equipment on full load for six hours, his energy consumption was 48 kWH. It can be concluded that (A) The load factor of consumer for the day was unity. (B) The maximum demand of consumer is 10 kW. (C) The equipment was drawing only reactive power. (D) The power factor of equipment was 0.8. 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is  (1) 122.8 GWh (2) 198.55 GWh (3) 128.2 GWh (4) 188.82 GWh

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 24 views

An industrial consumer hall a daily load pattern of 2000 KW, 0.8 lag for 12 Hra and 1000 kW UPF for 1J Hr. The load factor i= _____. 

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 54 views

A 1-phase, 7.46 kW motor is supplied from a 400 V, 50 Hz A.C mains. Its efficiency is 85% and power factor is 0.8 lagging. Calculate the KVA input (1) 9.56 kVA (2) 5.4 Kva (3) 10.97 kVA (4) 8.6 kVA 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

A relay has a rating of 5 A, 2.2 sec IDMT and a relay setting of 125% TMS = 0.6. It is connected to a supply circuit through a C.T. 400/5 ratio. The fault current is 4000 A. The operating current of the relay is

asked May 3, 2018 in Switchgear And Protection by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 34 views

A meter whose constant is 600 revolutions/kWh makes 5 revolutions in 20 seconds. Calculate the load in kW. (1) 0.5 kW (2) 1 kW (3) 1.5 kW (4) 2 kW  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 63 views

A consumer consumes. 600 kWh per day at a load factor of 0.40. If the consumer increases the load factor of 0.70 without increasing the maximum demand, what is the consumption of energy in kWh?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 19 views

A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

asked May 23, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 148 views

A 50 Hz, 4 pole turboalternator rated at 20 MVA. 13.2 KV has an inertia constant H = 4 KW sec/KVA. The K.E. stored in the rotor at synchronous speed is

asked May 3, 2018 in Electric Power Transmission by Shimroz123
1 answer 30 views

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 16 views

A 400 V, 15 kW, 4-pole, 50 Hz, Y-connected induction motor has full load slip of 4%. The output torque of the machine at full load is  (A) 1.66 Nm (B) 95.50 Nm (C) 99.47 Nm (D) 624.73 Nm

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 17 views

A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is  (A) 86.7% (B) 88.26% (C) 88.9% (D) 87.8%

asked May 17, 2018 in Transformer by Shimroz123
1 answer 28 views

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

asked May 17, 2018 in Electrical Machine by Shimroz123
0 answers 18 views

At maximum efficiency of a single-phase transformer, the load power factor is (A) unity (B) lagging (C) leading (D) zero 

asked Jun 4, 2018 in Single phase transformer by Shimroz123
1 answer 31 views

A three-phase synchronous motor connected to ac mains is running at full load and unity power factor. lf its shaft load is reduced by half and field current is held constant then its new power factor will be

asked Apr 28, 2018 in Electrical Machine by Shimroz123
1 answer 137 views

A 3-phase, 11 kv, 50 Hz, 200 kW load has a power factor of 0.8 lag. A delta connected 3-phase capacitor is used to improve the power factor to unity. The capacitance perphase of the capacitor in micro-farads is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 23 views

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

asked Apr 28, 2018 in Electrical Machine by Shimroz123
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

Which of the following sorts is quickest when sorting the following set: 1 2 3 5 4  (1) Quick Sort (2) Bubble Sort (3) Merge Sort (4) Heap Sort 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 11 views

Three capacitors 15µf, 18µf and 12µf are connected in a circuit. Find equivalent capacitance when they are connected in – 1) Series 2) Parallel

asked Sep 2, 2018 by Shimroz123
1 answer 51 views

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

asked May 8, 2018 in Electric Power Transmission by Shimroz123
0 answers 17 views

1 Ton (unit of air conditioning load) in terms of kW is   (a) 3.5 kW (b) 4.7 kW (c) 12 kW (d) 10.5 kW 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 131 views

MSXML is  (1) A Microsoft language (2) XML parser that ships with Internet explorer 5.0 (3) Used for interacting with XML (4) None of these

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 16 views

The load of a consumer is generally measured in terms of : (A) Volts (B) Amperes (C) Ampere hour (D) kW

asked May 8, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

The gain of a parabolic dish antenna of 1 m diameter -and 80% efficiency at 9.5 GHz is: a. 39 dB b. 78 dB c. 40 dB d. 45 dB

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 17 views

A three-phase star -connected load is operating at a power factor angle ϕ  with ϕ being the angle between

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each conductor is 0.5 ohm / km. Receiving end voltage is 33 kV. If the line loss is not to exceed 10%, determine the length of the line.  (A) 7 km (B) 27.9 km (C) 56.8 km (D) 13.9 km

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

When the SCR conducts, the forward voltage drop will   (a) 0.7 V at all load current (b) 2 to 2.5 V at all load current (c) increases slightly with load current (d) remains constant with load current 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

State the function of following components related to mimic diagram. 1) PL 2) OPL 3) CHL 4) GCK 5) LTK 6) ARK

asked Sep 2, 2018 by Shimroz123
0 answers 15 views

Total numbers of ascending runs in the sequence 4 6 7 2 9 1 2 8 9 3 0  (1) 3 (2) 5 (3) 7 (4) 9  

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 24 views

A ramp voltage V(t)=100 V is applied to an RC differentiating circuit with R=5 kΩ and C=4 μF. The maximum output voltage is  (A) 0.2 V (B) 2 V (C) 10 V (D) 50 V

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 5 views

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 53 views

A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is

asked May 8, 2018 in Electric Power Transmission by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,530 questions

7,129 answers

135 comments

3,090 users

...