13 views
in Digital Electronics by
In a positive edge triggered JK flip-flop, J = 1, K = 0 and clock pulse is rising, Q will be (a) 0 (b) 1 (c) showing no change (d) toggle 

1 Answer

0 votes
by

In a positive edge triggered JK flip-flop, J =1, K= 0 and clock pulse is rising, a Q will be 1

Related questions

1 answer 135 views

The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is A) 10 KHz B) 2.5 KHz C) 20 KHz D) 5 KHz

asked May 20, 2018 in Digital Electronics by Shimroz123
0 answers 49 views

 A J -K flip-flop with J= 1 and K= 1 has a 20 kHz clock input. The Q output is : (A) Constant and low (B) Constant and high (C) A square wave with 20 kHz frequency (D) A square wave with 10 kHz frequency

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

The output of a JK flip-flop with asynchronous preset and clear inputs is ‘1’. The output can be changed to ‘0’ with one of the following conditions by applying A) J = 0, K = 0 and using a clock B) J = 1, K = 0 and using the clock C) Asynchronous preset input D) J = 1, K = 1 and using the clock 

asked Jun 17, 2018 in Digital Electronics by Shimroz123
1 answer 9 views

Which of the following describes the operation of a positive edge - triggered D -type flip-flop? a) if both inputs are HIGH, the output will toggle b) the output will follow the input on the leading edge of the clock c) - when both inputs are LOW, an invalid state exists d) the input is toggled into the flip-flop on the leading edge of the clock and is passed to the output on the trailing edge of the clock.

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
0 answers 113 views

How is a J-K Flip Flop made to toggle  (a) J=0, K=0 (b) J=1, K=0 (c) J=0, K=1 (d) J=1, K=1 

asked May 23, 2018 in Digital Electronics by Shimroz123
1 answer 14 views

Read the following statements: i. Gate is a combinational logic. ii. JK Flip-flop in toggle mode is not combinational logic. iii. MSJK Flip-flop suffers from race-around. iv. Counters are sequential circuits. Which choice is correct? (A) i, ii (B) i, ii, iv (C) ii, iii, iv (D) i, ii, iii

asked May 24, 2018 in Digital Electronics by Shimroz123
1 answer 25 views

In a JK flip-flop, for what input next state is complement of the present state (A)J=0,K=0 (B)J=1,K=0 (C)J=0,K=1 (D)J=1,K=1

asked May 12, 2018 in Digital Electronics by Shimroz123
0 answers 14 views

By which of the following connections, one-bit binary counter can be obtained from a JK flip-flop?  A) J = K = 0 B) J = K = 1 C) J = K’ D) None of these

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 49 views

A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 8 views

Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency is (a) 2.65 MHz (b) 6.25 MHz (c) 5.26 MHz (d) 6.52 MHz 

asked May 26, 2018 in Electronics Engineering by Shimroz123
0 answers 19 views

A modulo -6 ripple counter with J-K flip-flops uses at the clear input, the output from (a) NAND gate with QB,Qc as inputs (b) NAND gate with QA, Q8 as inputs (c) NAND gate with QA, Qc as inputs (d) AND gate with QB, Qc as inputs

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 43 views

A thyristor is triggered by a pulse train of 5 kHz. The duty ratio is 0.4. If the allowable average power is 100 W, the maximum allowable gate drive power will be 

asked May 25, 2018 in Power Electronics by Shimroz123
1 answer 15 views
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

Define flip-flop.

asked Feb 19, 2018 in Digital Electronics by Fliop flop
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A basic S -R flip-flop can be constructed by cross -coupling which basic logic gates : - a) AND or OR gates b) XOR or XNOR gates c) NOR or NAND gates d) AND or NOR gates

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 86 views

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

asked Jun 18, 2018 in Microprocessors and Microcontrollers by Shimroz123
1 answer 8 views

Logic state 0 in positive logic corresponds to   1. zero voltage 2. positive voltage 3.higher voltage level 4. lower voltage level 

asked May 13, 2018 in Digital Electronics by Shimroz123
1 answer 3 views

State function of preset and clear in flip flop.

asked 3 days ago in Digital Techniques by Shimroz123
1 answer 12 views

How many flip-flops are required to build a binary counter circuit to count from 0 to 1023 ? (a) 1 (b) 6 (c) 10 (d) 23 

asked May 26, 2018 in Digital Electronics by Shimroz123
0 answers 13 views

A switch is connected in between a 12V battery and an uncharged capacitor and a 1 K Ohm resistor. At the time instant when the switch is closed, the voltage across the capacitor is :  A) 6V B) 12v C) 0V D) 24V

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

 When A = 0., B = 0, C = 1 then in two input logic gate we get gate  (A) XOR gate (B) AND gate (C) NAND gate (D) NOR gate

asked May 17, 2018 in Digital Electronics by Shimroz123
0 answers 7 views
0 answers 17 views

DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-300 A, what shunt resistance need to be connected?  A) 0.025 Ω B) 0.05 Ω C) 0.015 Ω D) 0.03 Ω

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

For the circuit shown in figure, the Boolean expression for the output y in terms of inputs P, Q, R and S is

asked May 20, 2018 in Digital Electronics by Shimroz123
1 answer 8 views

The magnetic field intensity at the centre of a current carrying coil of diameter J m is K. The current flowing in the coil is

asked May 24, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 16 views

In an unclocked R-S flip flop made of NOR gates, the forbidden input condition is:  (1) R=0, S=0 (2) R=1, S=0 (3) R=0, S=1 (4) R=1, S=1

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 3 views

Draw logic diagram of T flip-flop and give its truth table.

asked 3 days ago in Digital Techniques by Shimroz123
1 answer 8 views

A 4 bit counter is used to count from 0,1,2...n. Value of “n” is

asked May 14, 2018 in Digital Electronics by Shimroz123
0 answers 13 views

On a master slave flip-flop, master is enabled : (A) When gate is low (B) When gate is high (C) When gate is either low or high (D) None of the above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 6 views

What is the output voltage of a battery if 12 J of energy is expended in moving 1 C of charge?

asked Jul 1 by Shimroz123
0 answers 8 views

What is the output voltage of a battery if 6 J of energy is expended in moving 1 C of charge?

asked Jul 1 by Shimroz123
0 answers 7 views

What is the output voltage of a battery if 10 J of energy is expended in moving 1.25 C of charge?

asked Jul 1 by Shimroz123
1 answer 18 views

A 1ms pulse can be stretched to 1 s pulse by using (A) an astable multivibrator (B) a monostable multivibrator (C) a bistable multivibrator (D) a Schmitt trigger circuit

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 17 views

A 1 ms pulse can be converted into a 10 ms pulse by using  A) An astable mutivibrator B) A monostable multivibrator C) Bistable multivibrator D) J-K flip flop.

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 28 views
1 answer 26 views

lf slip of an induction machine is 0.02 and the stator supply frequency is 50 Hz, what will be the frequency of the rotor induced e.m.f.? (A) 10 Hz (B) 50 Hz (C) 1 Hz (D) 2500 Hz

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

A certain SRAM has CS=0, WE=0 and OE=1. In which the following mode, this SRAM is operating: a) Read b) Write c) Stand By d) None of the above

asked May 23, 2018 in Computer Engineering by Shimroz123
0 answers 17 views

A 12-bit ADC is operating with a lus clock period and total conversion time is seen to be 14us always. The ADC must be of the type  a. Flash type b. Counting type c. Integrating type d. Successive approximation type

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 18 views

To convert a S-R flip-flop to D flip-flop (a) D input is given to S and D input to clock (b) D input is given to S and D to R (c) D input is given to clock and D to S input (d) D input to S and clock to R

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

asked Dec 4, 2017 in Electrical Engineering by Quiz
1 answer 8 views

Which code is used in constructing k-maps?  A) Hamming code B) 2 out of 5 code C) BCD code D) Gray code 

asked Jun 17, 2018 in Digital Electronics by Shimroz123
0 answers 17 views

One of the necessary and sufficient condition for a network function N(s)=p(s)/q(s) to be a transfer function is that  A) The coefficients of the polynomial p(s) and q(s) must be real and those for q(s) must be positive B) Coefficients of p(s) and q(s) must be real and positive C) Coefficients of p(s) must be positive and real but coefficients of q(s) can be negative also D) Degree of p(s) and q(s) may differ by either zero or one only

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 32 views

A series RLC circuit has a resonant frequency of 1 KHz and a quality factor Q = 100. If each of the R,L and C is doubled from its original value, the new Q of the circuit is:  (1) 25 (2) 50 (3) 100 (4) 200

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 23 views

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 39 views

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

asked May 3, 2018 in Electrical machine design by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...