23 views
in Analog electronics circuits by
The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is: (1) 500 Hz (2) 700 Hz (3) 300 Hz (4) 1400 Hz 

1 Answer

0 votes
by

The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is: 300 Hz

Related questions

1 answer 33 views

The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: (1) 1/100 (2) 1/200 (3) 1/300 (4) 1/600 

asked May 28, 2018 in Analog electronics circuits by Shimroz123
0 answers 19 views

A signal m(t) = 3cos(6000nt)+4cos(7000nt)+5cos(100001-it) to be sampled. What is the minimum sampling rate for band pass sampling for truth full representation : a. 2000 Hz b. 3000 Hz c. 5000 Hz d. 10000 Hz

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 37 views

As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by (symbols/notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 47 views

The signal x(t) = sin(t)/t is  A) Even function B) Odd function C) Neither odd nor even D) Both odd and even

asked Apr 9, 2018 in Digital Signal Processing by Shimroz123
0 answers 45 views

The sampling rate to avoid aliasing for the signal m(t) = 100 cos 200ωt will be A) ≥1/25 sec B) ≥1/50 sec C) ≤1/25 sec D) ≤ 1/50 sec

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

The p.u. parameter for a 500 MVA machine on its own base are: inertia, M = 20 p.u. ; reactance, X = 2 p.u. The p.u. values of inertia and reactance on 100 MVA common base, respectively, are (A) 4, 0.4 (B) 100, 10 (C) 4, 10 (D) 100, 0.4

asked May 25, 2018 in Power system by Shimroz123
0 answers 29 views

The step angle of the stepper motor is 2.5°. If the stepping frequency is 3600 pulses per second, then the shaft speed will be   (a) 144 rps (b) 3600 rps (c) 25 rps (d) 2.5 rps 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is  (A) 50.0% (B) 70.7% (C) 141.4% (D) 200.0%

asked May 17, 2018 in Transformer by Shimroz123
0 answers 46 views

In order to recover the original signal from the Sampled one, what is the condition to be satisfied for sampling frequency ωs and highest frequency component ωm?  (A) ωm < ωs ≤ 2 ωm (B) ωs ≥ 2 ωm (C) ωs < ωm (D) ωs = ωm

asked Apr 5, 2018 in Electrical Engineering by Zeeshan
1 answer 28 views

Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is (A) causal & linear (B) non-causal & linear (C) causal & non-linear (D) non-causal & non-linear

asked Apr 26, 2018 in Control System by Shimroz123
0 answers 45 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 20 views

An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided

asked May 12, 2018 in Control System by Shimroz123
1 answer 16 views

A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately? A.15.1 μA B.151 μA C.66 mA D.660 mA

asked May 15, 2018 in Basic concepts by Zeeshan
0 answers 14 views

Pick up the false statement from the choices given below : (A) In a 3 -ph balanced delta circuit, phase voltage is same as line voltage (B) In a 3 -ph balanced delta circuit, phase current is same as line current (C) In a 3 -ph balanced star circuit, line voltage is 1.73 times phase voltage (D) In a 3 -ph balanced star circuit, phase current is same as line current 

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 9 views

The current i(t), through a 10 Ω resistor in series with an inductance, is given by I(t) = 3 + 4sin (100t + 450 ) + 4 sin(300t +600) amperes. The RMS values of the current and power dissipation in the circuit are:  (A) √41 A, 410 W respectively (B) √35 A, 350 W respectively (C) 5 A, 250 W respectively (D) 11 A, 1210 W respectively

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A 500 W bulb fitted with a reflector illuminates an area of 2 m x 2 m with an average illumination of 500 lux. The efficiency of the reflector is 50%. The efficiency of the bulb in lumens/watt is : 

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 25 views

The standard for long distance analog signal transmission in process control industry is (A) 4-20 mV (B) 0-20 mA (C) 4-20 mA (D) 0-5 V

asked Apr 26, 2018 in Control System by Shimroz123
1 answer 40 views

 If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 47 views

For a given base voltage and base volt-amperes, the per unit impedance value is x. For the doubled base values of both voltage and volt-amperes, the per unit impedance will be (a) 2x (b) 0.25x (c) 0.5x (d) no change 

asked May 25, 2018 in Battery by Shimroz123
0 answers 21 views

Which of the following can‟t be declared static?  (1) Member variables (2) Object (3) functions (4) none of these

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 27 views

For a 1.8o, 2-phase bipolar stepper motor, the stepping rate is 100 steps/second. The rotational speed of the motor in rpm is  (A) 15 (B) 30 (C) 60 (D) 90

asked May 17, 2018 in Electrical Machine by Shimroz123
0 answers 9 views

If a current of 500 mA charges a dielectric for 2 s, how much charge is stored in the dielectric?

asked Jul 1 by Shimroz123
0 answers 49 views

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 63 views

For an analog PLL, under perfect locking condition, the phase difference (in degrees) between input signal and VCO output should be  A) 0 B) 90 C) 120 D) 180

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

______ signal is generated by combining RD and WR signals with IO/M.   (a) Control (b) System (c) Register (d) Memory

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 122 views

The impedance of a circuit is given by z=3+j4. Its conductance will be?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

asked Apr 29, 2018 in Electrical Machine by Shimroz123
0 answers 20 views

Propagation medium of the signal in band (3 to 30) MHz is by  A) Space wave B) Surface wave C) Sky wave D) LOS

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 15 views

The fastest logic family among the below given ones is  A) TTL B) ECL C) CMOS D) I 2 L

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 33 views

A carrier signal of 600 V rms with 75% amplitude modulation is applied to 75 ohm antenna. The total side band power (in watts) is  A) 4800 B) 450 C) 950 D) 1350 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

asked Mar 21, 2018 in DC generator by Shimroz123
1 answer 15 views

What is the maximum value of a load which consume 500 KWh per day at a load factor of 0.40, if the consumer increases the load factor of 0.50 without increasing the maximum demand? 

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 185 views

For a 66 kV line having span of 200 meters between towers the approximate sag will be 2 m. If the span is double the sag will be:  (A) 1 m (B) 2 m (C) 4m (D) 8m

asked May 8, 2018 in Electric Power Distribution by Shimroz123
1 answer 11 views

The rotor frequency for a 3-phase 6-pole, 1000 r.p.m. induction motor with a slip of 0.04 is (a) 2 Hz (b) 4 Hz (c) 6 Hz (d) 8 Hz  

asked May 25, 2018 in Induction Machine by Shimroz123
1 answer 8 views

Indicate which of the following pulse modulation is analog  a) PCM b) DPCM c) PWM d) Delta

asked May 23, 2018 in Analog electronics circuits by Shimroz123
0 answers 27 views

What is the difference between analog and digital electronics?

asked Mar 10, 2018 in Analog electronics circuits by Quiz
0 answers 25 views

What is the analog circuit?

asked Mar 10, 2018 in Analog electronics circuits by Quiz
1 answer 65 views

Number of commutator bars for a 4-pole, 2-layer, DC lap winding with 24 slots and one conductor per layer is (A) 48 (B) 24 (C) 192 (D) 96

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
0 answers 23 views

The constant of a given energy meter is 500 revolution/kWh. At the test 4.4 kW full load, meter completes 50 revolutions in 86 seconds. The percentage error of the meter is (a) –4.86% (b) 4.86% (c) 2.0% (d) 3.0%

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 22 views

The dc gain of the system represented by the transfer function G(s)=(s+6)/((s+2)(s+3)) is  A) 1 B) 2 C) 5 D) 6

asked Apr 9, 2018 in Control System by Shimroz123
0 answers 22 views

 In which type of the faults given below, all of the three components Ia0, Ia1 and Ia2 are equal?  (A) Single line to ground fault (B) Double line to ground fault (C) Line to line fault (D) 3 phase faults

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

The FS of a periodic continuous-time signal x(t) is  A) Continuous Complex-valued function B) Discrete Real-valued function C) Continuous Real-valued function D) Discrete Complex-valued function

asked Apr 9, 2018 in Digital Signal Processing by Shimroz123
1 answer 16 views

The change in value of an analog signal during the conversion process produces what is called the : -  a) quantization error b) resolution error c) Nyquist error d) sampling error

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

For a round wire, the approximate value of fusing current is given by

asked May 3, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

What is an example of an analog device?

asked Mar 10, 2018 in Analog electronics circuits by Quiz
0 answers 13 views

What is an analog voltage?

asked Mar 10, 2018 in Analog electronics circuits by Quiz

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...