Can you help by answering this question?

Who created the Arduino?

25 views
in Amplifier by
An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

1 Answer

0 votes
by

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

Related questions

1 answer 28 views

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 34 views

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 67 views

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

asked May 3, 2018 in Power Electronics by Shimroz123
0 answers 39 views

An amplifier which has almost same gain and input resistance of a CE amplifier but of higher bandwidth is  A) Cascode amplifier B) Cascade amplifier C) Darligton amplfier D) CC amplifier

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 90 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
0 answers 15 views

The total output offset voltage for a noninverting amplifier with input resistance 1 kOhm , feedback resistance 10 k Ohm, input offset voltage 10 mV and input bias current 100 nA is, about  A) 25 mV B) 55 mV C) 110 mV D) 220 mV

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
1 answer 11 views

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 34 views

An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

asked May 1, 2018 in Power Electronics by Shimroz123
1 answer 12 views

An amplifier has a voltage gain of 50; this gain in dB will be (A) 34 dB (B) 68 dB (C) 41 dB (D) 14 dB 

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
1 answer 14 views

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

asked May 17, 2018 in Amplifier by Shimroz123
1 answer 27 views

A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 30 views

The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 11 views

An Op-amp as a voltage follower has a voltage gain of

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 21 views

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 15 views

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 23 views

The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

asked May 13, 2018 in Amplifier by Shimroz123
1 answer 16 views

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

asked May 17, 2018 in Electronics communication by Shimroz123
0 answers 30 views
1 answer 26 views

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

asked Jun 18, 2018 in Amplifier by Shimroz123
1 answer 15 views

The gain of an FET amplifier can be changed by changing: (1) rm (2) gm (3) Rd (4) None of these

asked May 28, 2018 in Amplifier by Shimroz123
1 answer 24 views

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

asked May 12, 2018 in Amplifier by Shimroz123
0 answers 15 views

With the introduction of negative feedback, the gain—bandwidth product of an amplifier  A) Becomes infinity B) Increases C) Decreases D) Remains constant

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 45 views

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

asked May 3, 2018 in Power system by Shimroz123
1 answer 12 views

A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage of 240 V at no load. The core has mean area of 30 cm2 and the flux density has not to exceed 1.3T. The number of secondary turns will be (a) 1270 (b) 1017 (c) 768 (d) 277  

asked May 25, 2018 in Single phase transformer by Shimroz123
1 answer 17 views

Negative feedback in an amplifier is accompanied by (A) Gain less sensitive to component variations (B) Increase in gain (C) Decrease in bandwidth (D) None of the above

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 23 views

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave 

asked May 29, 2018 in Amplifier by Shimroz123
0 answers 10 views

A SCR has an anode supply of sine voltage 200V rms, 50 Hz applied through a 100Q resistor and fired at an angle of 60°. Assuming no voltage drop, the rms value of the output voltage is : (A) 89,7 V (B) 126.7 V (C) 166.7 V (D) 288.28 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

A certain common-emitter amplifier has a voltage gain of 100. If the emitter bypass capacitor is removed.  a. The circuit will become unstable b. The voltage gain will decrease  c. The voltage gain will increase d. The circuit will become stable

asked Aug 31, 2018 by Shimroz123
1 answer 8 views

Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

asked Sep 2, 2018 by Shimroz123
1 answer 12 views

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) 1.0 ohm in series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 49 views

A high-pass filter has a resistance R = 2 kΩ The lowest input frequency to be passed is 7.5 kHz. The value of suitable coupling capacitor must be: A) 0.001 pico Farad B) 0.01 pico Farad C) 0.1 pico Farad D) 1 pico Farad

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
0 answers 33 views

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

asked Apr 4, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop gain is (a) 1 (b) 1,00,000 (c) 50 (d) 0.02

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 52 views

A dominant pole compensated op-amp has openloop gain of 100 dB and -3 dB bandwidth of 50 Hz. If it is connected as inverting amplifier for a gain of 20 dB the -3 dB bandwidth is about  A) 500 kHz B) 50 kHz C) 5 kHz D) 500 Hz

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
1 answer 58 views

A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 8 views

Which of the following amplifier configurations has the lowest input resistance?  A) Common Emitter B) Common Base C) Common Collector D) Emitter Follower

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

A high pass filter has a resistance R = 2 kΩ. The lowest input frequency to be passed is 7.5 KHz. The value of suitable coupling capacitor must be : (A) 0.1 pF (B) 1 pF (C) 0.1 μ F (D) 1 μ F

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 54 views

The main function of the transformer used in the output of a power amplifier is  (A) To step up the voltage  (B) to increase the voltage gain  (C) to safeguard the transistor against overheating  (D) to match the load impedance with dynamic output resistance of the transistor

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 8 views

Differentiate between positive and negative feedback on the basis of . (i) overall phase shift (ii) voltage gain (iii) stability (iv) applications 

asked Jul 10 in Elements of Electronics by Shimroz123
1 answer 16 views

A negative feedback loop returning a voltage to the input raised the input impedance and making the circuit a better

asked May 23, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

What is the importance of negative feedback in the operational amplifier? (A) It maintains the gain (B) The voltage difference between the input terminals is maintained at a very small value (C) The voltage difference between the input terminals is maintained at a constant value (D) The voltage difference between the input terminals is maintained at a very high value

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 14 views

For a feedback control system of type 2, the steady error for a rap input is  A) Infinite B) Constant C) Zero D) Indeterminate

asked May 20, 2018 in Control System by Shimroz123
1 answer 148 views

A 50 Hz, 4 pole turboalternator rated at 20 MVA. 13.2 KV has an inertia constant H = 4 KW sec/KVA. The K.E. stored in the rotor at synchronous speed is

asked May 3, 2018 in Electric Power Transmission by Shimroz123
1 answer 46 views

In a differential amplifier the differential voltage gain is 500 and the common mode voltage gain is 0.5. The CMRR in dB is (a) 80 (b) 60 (c) 30 (d) 20

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 77 views

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

The input frequency of a bridge rectifier is 50 its output frequency will be  1. 25 Hz 2.50 Hz 3.75 Hz 4. 100 Hz

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 9 views

A series RLC circuit has a resistance of 50 , inductance of 0.4H and a capacitor of 10µF. The circuit is connected across a 100V supply. The resonance frequency and the current through the resistance are 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
0 answers 49 views

 A J -K flip-flop with J= 1 and K= 1 has a 20 kHz clock input. The Q output is : (A) Constant and low (B) Constant and high (C) A square wave with 20 kHz frequency (D) A square wave with 10 kHz frequency

asked Apr 14, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...