21 views
in Electronics communication by
Which of the following is an inherent property of an optical signal and cannot be eliminated even in principle? (1) Thermal noise (2) Shot noise (3) Environmental noise (4) Background Noise

1 Answer

0 votes
by

Which of the following is an inherent property of an optical signal and cannot be eliminated even in principle? (1) Thermal noise (2) Shot noise (3) Environmental noise (4) Background Noise

Related questions

1 answer 13 views

The following property of semiconductors cannot be determined from Hall effect: (1) Semiconductor is n–type or p–type (2) The carrier concentration (3) The mobility of semiconductor (4) The atomic concentration of semiconductor

asked May 29, 2018 in Semiconductor by Shimroz123
0 answers 80 views

Which of the following devices cannot be used as microwave oscillator : a. IMPATT diode b. PN Junction .diode c. TRPATT diode d. BARRITT diode

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided

asked May 12, 2018 in Control System by Shimroz123
1 answer 12 views

In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is

asked May 23, 2018 in Electronics communication by Shimroz123
0 answers 13 views

Following is/are a property/properties of quantization  (a) it is an nonlinear process (b) it is an irreversible process (c) it maps a larger set of input values to a smaller set  (d) all of these 

asked Apr 9, 2018 in Electronics communication by Shimroz123
1 answer 17 views

Indicate which one of the following is NOT an advantage of FM over AM? (1) Better noise immunity is provided (2) Lower bandwidth is required (3) The transmitted power is more useful (4) Less modulating power is required 

asked May 29, 2018 in Electronics communication by Shimroz123
1 answer 60 views

To read or write a complete word from / to the memory in 8086 microprocessor and if it is located at an even address, the number of Read or Write cycles required is

asked May 23, 2018 in Microprocessors and Microcontrollers by Shimroz123
1 answer 8 views

Which property of rubber is used in tyres? Name and explain the property. 

asked Sep 3, 2018 by Shimroz123
1 answer 10 views

In C# which of the operators cannot be overloaded  A) ! B) = C) + D) all of the above

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 14 views

In single pulse modulation of PWM inverters, third harmonic can be eliminated if pulse width is equal to   (a) 30o (b) 60o (c) 120o (d) 150o

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 24 views

The property of materials by which they can be drawn into wires is known as: A) malleability B) elasticity C) creep D) ductility

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
0 answers 304 views

The difference of the reference input and the actual output signal is called  (a) error signal (b) controlling signal (c) actuating signal (d) transfer function

asked Apr 9, 2018 in Electronics communication by Shimroz123
0 answers 9 views

Which of the following lamp cannot sustain much voltage fluctuations (1) Sodium vapour lamp (2) Mercury vapour lamp (3) Incandescent lamp (4) Fluorescent lamp 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

Which wave cannot exist inside wave guide  (A) TE (B) TM (C) TEM (D) HE

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 13 views

Which of the following oscillators is used for generation of high frequency signal ? (a) RC phase shift oscillator (b) Blocking oscillator (c) Wein bridge oscillator (d) L-C oscillator 

asked May 26, 2018 in Electronics Engineering by Shimroz123
1 answer 21 views

The property of a material which opposes the creation of magnetic flux in it is known as?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

Following type of multiplexing cannot be used for analog signalling  (a) FDM (b) TDM (c) CDM (d) None of these

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

Which of the following statement is false? Modulation is used to: (1) Reduce the bandwidth used (2) Separate differing transmissions (3) Ensure that intelligence may be transmitted over long distances (4) Allow the use of practicable antennas

asked May 29, 2018 in Electronics communication by Shimroz123
1 answer 31 views

Which of the following instrument can be used for measuring speed of an aeroplane ? (A) orifice plate (B) hot wire anemometer (C) rotameter (D) pitot tube

asked Jun 15, 2018 in Mechanical Engineering by Shimroz123
1 answer 13 views

Principle of Doppler effect is used in

asked May 23, 2018 in Electronics communication by Shimroz123
1 answer 17 views
1 answer 13 views

Why energy conservation techniques should be adopted in transformers even though its efficiency is 90%? 

asked Oct 3, 2018 in Energy Conservation And Audit by Shimroz123
1 answer 14 views

 In thermo-couple instruments, in which of the following is an emf caused if the junction of two wires of dissimilar metals is heated and the free or cold ends are connected to a milli-voltmeter? A) Kelvin effect B) Hot wire effect C) Seebeck effect D) Faraday effect 

asked Jun 17, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

Which of the following will happen if a voltmeter is connected like an ammeter in series to the load ? (A) There will be almost no current in the circuit. (B) The meter will burn. (C) The measurement will be trio high. (D)  A very high current will flow.

asked May 12, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

Which if the following operation is the easiest in terms of time as a resource  (1) Accessing an element (2) deletion of an element (3) Insertion of an element (4) creation of Array of given size 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 31 views

Which of the following devices is used to measure flow in an open channel ?   (a) Venturimeter (b) Rota meter (c) Orifice (d) Pitot tube 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

The speed and torque of induction motors can be varied by which of the following means: 1) Stator voltage control 2) Rotor voltage control 3) Frequency control 4) All of these

asked Jun 4, 2018 in Induction Machine by Shimroz123
1 answer 12 views

For an antenna to be frequency-independent, it should expand or contract in proportion to the  (a) gain (b) directivity (c) wavelength (d) impedance

asked May 15, 2018 in Electronics communication by Zeeshan
1 answer 13 views

An HVDC link consist of rectifier, inverter transmission line and other equipments. Which one of the following is true for this link ?  (A) The transmission line produces/ supplies reactive power (B) The rectifier consumes reactive power and the inverter supplies reactive power from/ to the respective connected ... power to/ from the respective connected AC systems (D) Both the converters (rectifier and inverter) consume reactive power from the respective connected AC systems

asked May 25, 2018 in Power system by Shimroz123
1 answer 11 views

State principle of optical fibre. 

asked Sep 3, 2018 by Shimroz123
1 answer 15 views

Which of the following function is useful in system requiring error detection and correction codes ? (A) AND-OR (B) OR (C) AND (D) Exclusive -OR

asked May 12, 2018 in Digital Electronics by Shimroz123
1 answer 7 views

What is encoder? Draw and explain an optical encoder operation for rotary motion measurement.

asked Sep 13, 2018 by Shimroz123
0 answers 26 views

For a waveform to be expressed in Fourier series, which of the following conditions must be satisfied? I. Maxwell’s conditions, II. Drichlet conditions, III. Sampling Theorem A) I only B) II only C) II and III only D) I, II and III

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 391 views

In which of the following transmission lines, the value of the Shunt admittance should be approximated to zero ? (A) A 66 kV 35 km long line (B) A 132 kV 200 km long line (C) A 220 kV 300 km long line (D) A 400 kV 500 km long line

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 16 views

In a Bode magnitude plot, which one of the following slopes would be exhibited at high frequencies by a 4th order all-pole system? (A) – 80 dB/decade (B) – 40 dB/decade (C) +40 dB/decade (D) +80 dB/decade

asked Apr 26, 2018 in Control System by Shimroz123
1 answer 15 views

The 555 timer can be used in which of the following configurations ?  a) astable, monostable b) monostable, bistable c) astable, toggled d) bistable, tristable

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
0 answers 17 views

Which of the following permutation can be obtained in the output (in the same order) using a stack assuming that the input is the sequence 1, 2, 3, 4, 5 in that order?  (1) 3, 4, 5, 1, 2 (2) 3, 4, 5, 2, 1 (3) 1, 5, 2, 3, 4 (4) 5, 4, 3, 1, 2 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 16 views

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 13 views
1 answer 43 views

As we know when there is a joint in optical fiber then there will be some loss then this loss be minimized by  a. Using index matching fluid in the gap b. Making V-grooved splicing c. Both (a)and (b) d. Making carefully polishing

asked May 17, 2018 in Telecommunication Engineering by Shimroz123
1 answer 9 views

Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is  (A) The transistor itself  (B) the power supply Vcc  (C) the coupling capacitor Cc  (D) the biasing resistors

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 16 views

The change in value of an analog signal during the conversion process produces what is called the : -  a) quantization error b) resolution error c) Nyquist error d) sampling error

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

The property of sand due to which the sand grains stick together, is called 1. Collapsibility 2. Permeability 3. Cohesiveness 4. Adhesiveness

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 16 views

Which type of flow is measured by hot wire anemometer and describe its working principle with suitable diagram. 

asked Sep 13, 2018 by Shimroz123
0 answers 17 views

In an axial mode operation of a helical antenna, maximum field radiated by the antenna is :  A) along the axis of the helical B) in a plane normal to the helix antenna axis C) in both axial and normal planes D) None of the above

asked Apr 9, 2018 in Electronics communication by Shimroz123
1 answer 97 views

If a voltage-controlled bus is treated as load bus, then which one of the following limits would be violated?   (a) Active power (b) Reactive power (c) Voltage (d) Phase angle 

asked May 13, 2018 in Power system by Shimroz123
1 answer 43 views

In the 8085A Microprocessor, arithmetic and logical operations are performed through which of the following? A) Stack B) ALU C) I/O D) Register 

asked Jun 18, 2018 in Microprocessors and Microcontrollers by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...