24 views
in Amplifier by
When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave 

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: Approaches to triangular waveshape

Related questions

1 answer 34 views

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

The output Y of a 2-bit comparator is logic 1 whenever the 2-bit input A is greater than the 2-bit input B. The number of combinations for which the output is logic 1, is  (A) 4 (B) 6 (C) 8 (D) 10

asked May 18, 2018 in Digital Electronics by Shimroz123
1 answer 14 views

A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of? B.12 kHz C.18 kHz D.1.3 MHz

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 17 views

The initial response when the output is not equal to input is called?

asked Mar 27, 2018 in Control System by Shimroz123
1 answer 17 views

When sine wave is given as input to Schmitt trigger then it generates : (A) Sine wave (B) Saw tooth wave (C) Triangle wave (D) Square wave

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 18 views

The transient current in lossless L-C circuit when excited from an AC source is, sine wave  (a) Critically damped (b) Underdamped (c) Overdamped (d) Undamped

asked May 16, 2018 in Electronics Engineering by Shimroz123
1 answer 24 views

Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

asked Sep 14, 2018 by Shimroz123
1 answer 26 views

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

asked May 29, 2018 in Amplifier by Shimroz123
1 answer 41 views

The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is_______Vs.

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 70 views

An op-amp having a slew rate of 62.8 V/msec, is connected in a voltage follower configuration. If the maximum amplitude of the sinusoidal input is 10 V, then the minimum frequency at which the slew rate limited distortion would set in at the output is  (A) 1 MHz (B) 6.28 MHz (C) 10 MHz (D) 62.8 MHz

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 37 views

When the wave travels in a conducting medium, the rate of attenuation is decided by

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 77 views

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 11 views

A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ? (A) 1.5 V/μs (B) 1.05 V/μs (C) 0.15mV/s (D) 10.5 mV/s

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

The input impedance of an op-amp is • High • Low • Medium • None of the above

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 12 views

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

asked Jul 10 in Elements of Electronics by Shimroz123
1 answer 19 views

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

asked Sep 5, 2018 by Shimroz123
1 answer 22 views

If the input to a differentiating circuit is a saw-tooth wave, then output will be …………….. wave: A) square B) rectangular wave C) triangular wave D) rectified sine wave

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 17 views

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 19 views

When a sine wave has a frequency of 100 Hz in 12 s it goes through? A.1/100 cycle B.12 cycles C.120 cycles D.1,200 cycles

asked May 15, 2018 in Basic concepts by Shimroz123
0 answers 95 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
1 answer 11 views

The threshold effect in demodulators is a) The rapid fall of output SNR when the input SNR falls below a particular value b) Exhibited by all the demodulators when the input SNR is low c) Exhibited by all AM suppressed carrier coherent demodulators d) Exhibited by correlation receivers

asked Jun 15, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

Why the emf of a cell is always greater than its terminal voltage? Explain the same.

asked Jul 5 by Shimroz123
1 answer 20 views

Which of the following statements is true?  (1) steady-state stability limit is greater than transient stability limit  (2) steady-state stability limit is equal to transient stability limit  (3) steady-state stability limit is less than the transient stability limit  (4) no generalization can be made regarding the equality or otherwise of the steady-state stability limit and transient stability limit

asked Apr 29, 2018 in Switchgear And Protection by Shimroz123
1 answer 15 views

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 12 views

The output of an exclusive–NOR gate is 1. Which input combination is correct? (1) A = 1, B = 0 (2) A = 0, B = 1 (3) A = 0, B = 0 (4) None of these 

asked May 28, 2018 in Digital Electronics by Shimroz123
1 answer 34 views

The ratio of rotor output to rotor input in an induction motor is 0.96. The slip of the motor is (a) 0.04% (b) 4% (c) 6% (d) 12%

asked May 25, 2018 in Induction Machine by Shimroz123
1 answer 67 views

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

asked May 3, 2018 in Power Electronics by Shimroz123
0 answers 22 views

When a sinusoidal voltage wave drives a Schmitt Trigger, the output is a:  A) Triangular wave B) Rectified sine wave C) Rectangular wave D) Trapezoidal wave

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 8 views

Slew rate is defined by: (1) di/dt(max) (2) dv/dt(max) (3) di/dt(min) (4) dv/dt(min) 

asked May 29, 2018 in Electronics Engineering by Shimroz123
0 answers 14 views

 Slew rate is expressed in : (A) A/microsec (B) V/microsec (C) W/microsec (D) None of the above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Materials having electrical conductivity much less than most of the metals but much greater than that of typical insulators, are known as A. Thermistors B. Varistors C. Semi-conductors D. Variable resistors. 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

_______are the materials having electrical conductivity much less than most of the metals but much greater than that of typical insulators.

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 20 views

The closed loop gain of an OPAMP is dependent upon, whether the OP AMP is used : -  a) in inverting mode b) in non -inverting mode c) is independent of the fact whether the input is connected to inverting or non -inverting terminal d) is depending upon the fact whether the input is connected to inverting or non -inverting terminal

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 18 views

The large signal bandwidth of an opamp is limited by its:  (1) Loop gain (2) Slew rate (3) Output impedance (4) Input frequency

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

The average value of a 12 V peak sine wave over one complete cycle is? A.0 V B.1.27 V C.7.64 V D.6.37 V

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 10 views

If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

asked May 15, 2018 in Basic concepts by Shimroz123
0 answers 11 views

What is the average value of a perfect sine wave over a complete cycle ? (A) Zero (B) Peak value (C) rms value (D) None of the above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
2 answers 239 views

The equation of 50 Hz current sine wave having r.m.s. value of 60 A is?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: A. 8.57% B. 42.85% C. 4.28% D. 85.7%

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 681 views

A motor load system is stable when the slope of the torque speed characteristics of the motor is (a) higher than the slope of the torque speed characteristics of the load (b) lower than the slope of the torque speed characteristics of the load (c) zero (d) none of the above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 9 views

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

asked Jul 10 in Elements of Electronics by Shimroz123
0 answers 16 views

Output of an op-amp is a square wave of 4 V peak to peak with a rise time of 5 microsecond and fall time of 4 microsecond.Maximum frequency (in kHz)of undistorted sine wave output of 2 V peak to peak is about  A) 100 B) 150 C) 200 D) 250

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 12 views

The ASCII is an input output code : - a) it is a two bit code b) it is a four bit code c) it is a seven bit code d) it is a eight bit code

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 17 views

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 15 views

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 21 views

When the initial conditions of a system are specified to be zero it implies that the system is?

asked Mar 27, 2018 in Control System by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,514 questions

7,113 answers

135 comments

3,090 users

...