Can you help by answering this question?

Name any 4 types of scalar objects?

16 views
in Electrical Engineering by
If Voltage Standing Wave Ratio, (VSWR) of a wave is 2, its reflection coefficient will be _____.

1 Answer

0 votes
by

If Voltage Standing Wave Ratio, (VSWR) of a wave is 2, its reflection coefficient will be 1/3.

Related questions

1 answer 12 views

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

asked May 29, 2018 in Electrical Engineering by Shimroz123
0 answers 38 views

Ideally Voltage Standing Wave Ratio (VSWR) should be  (a) as large as possible (b) as small as possible (c) as close to unity as possible (d) infinity

asked Apr 9, 2018 in Electronics communication by Shimroz123
1 answer 54 views

If a transformer primary is energised from a square wave voltage source, its output voltage will be a:  (A) square wave (B) sine wave (C) triangular wave (D) pulse wave

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 122 views

A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 62 views

If the inertia constant H of a machine of 200 MVA is 2 p.u., its value corresponding to 400 MVA will be   (a) 4 p.u. (b) 2 p.u. (c) 1.0 p.u. (d) 0.5 p.u. 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The reflection coefficient of a short-circuited line for voltage is: A) -1 B) +1 C) 0.5 D) zero

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In a system, the damping coefficient is - 2. The system response will be (a) Undamped (b) Oscillations with decreasing magnitude (c) Oscillations with increasing magnitude (d) Critically damped

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

The r.m.s. value of a half-wave rectified alternating current is 10 A. Its value for full-wave rectification will be  

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

If a capacitance is charged by a square wave current source, then the voltage across the capacitor will be (a) Square wave (b) Step function (c) Triangular wave (d) Zero

asked May 25, 2018 in Capacitance by Shimroz123
1 answer 23 views

The coefficient of reflection for current wave is

asked May 3, 2018 in Physics by Shimroz123
1 answer 12 views

A transmission line is terminated at its characteristic impedance. The reflection coefficient is  (a) 1 (b) –1 (c) 0 (d) ∞

asked May 16, 2018 in Network Analysis by Shimroz123
1 answer 17 views

 If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.

asked May 29, 2018 in Transducers and sensors by Shimroz123
0 answers 29 views

For a battery with constant voltage, the reflection coefficient is (a) ∞ (b) – 1 (c) 1 (d) 0 

asked May 25, 2018 in Battery by Shimroz123
0 answers 19 views

If frequency is decreased 4 times, then skin depth of an Electromagnetic wave inside a conductor will be :  A) halved B) quadrupled C) doubled D) no change

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 87 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
1 answer 185 views

For a 66 kV line having span of 200 meters between towers the approximate sag will be 2 m. If the span is double the sag will be:  (A) 1 m (B) 2 m (C) 4m (D) 8m

asked May 8, 2018 in Electric Power Distribution by Shimroz123
1 answer 14 views

If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be

asked Apr 29, 2018 in Power system by Shimroz123
0 answers 12 views

The ratio of the primary to secondary voltage of a transformer is 2:1. The saving in the turns of weight of copper required if an autotransformer is used instead of two winding transformer is (1) 50% (2) 33.33% (3) 66.67% (4) 97% 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is :  (A) 2.8 (B) 2.6 (C) 4.6 (D) 3.6

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

If the input to a differentiating circuit is a saw-tooth wave, then output will be …………….. wave: A) square B) rectangular wave C) triangular wave D) rectified sine wave

asked Jun 4, 2018 in Power Electronics by Shimroz123
0 answers 18 views

If the transmission line is loaded with leading reactive volt amperes, there will be rise of voltage at the receiving end and this (a) increases (b) decreases (c) remains same with the increase in the length of line (d) none of these

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 66 views

A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

asked Apr 29, 2018 in Power Electronics by Shimroz123
0 answers 17 views

In case of open circuited transmission lines the reflection coefficient is given by (A) 1 (B) -1 (C) 0.5 (D) 0

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 50 views

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 29 views

if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

asked Dec 4, 2017 in Electrical Engineering by Quiz
2 answers 52 views

If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

asked Oct 21, 2017 in Electrical Engineering by Quiz
1 answer 7 views

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

asked 6 days ago in Elements of Electronics by Shimroz123
1 answer 70 views

A voltage source inverter will have better performance if its  (1) load inductance is small and source inductance is large.  (2) both load and source inductance are small.  (3) both load and source inductances are large.  (4) load inductance is large and source inductance is small. 

asked Apr 30, 2018 in Power Electronics by Shimroz123
0 answers 7 views

Using a quarter wave transformer of characteristic impedance 1 Ohm, a load impedance of 100 Ohm will be transformed to an input impedance of value :  A) 1 Ohm B) 100 Ohm C) 0.01 D) 0.1 Ohm

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

If the load current and flux of a DC motor are held constant, and voltage applied across its armature is increased by 10%, its speed will:  (A) Decrease by 10%. (B) Remain unchanged. (C) Increase by 10%. (D) Increase by 20%. 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 135 views

In a pure capacitive circuit if the supply frequency is reduced to 1/2, the current will?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 47 views

In a pure inductive circuit if the supply frequency is reduced to 1/2, the current will?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-300 A, what shunt resistance need to be connected?  A) 0.025 Ω B) 0.05 Ω C) 0.015 Ω D) 0.03 Ω

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

If both the number of turns and core length of an inductive coil are doubled, then its self inductance will be (a) halved (b) doubled (c) quadrupled (d) unaffected

asked May 25, 2018 in Inductance by Shimroz123
1 answer 39 views

 In an alternator if the winding is short pitched by 60 electrical degrees, its pitch factor will be: A) 1.0 B) 0.866 C) 0.75 D) 0.50

asked Jun 4, 2018 in Alternator by Shimroz123
2 answers 105 views

If a positively charged body is placed inside a spherical hollow conductor, what will be the polarity of charge inside and outside the hollow conductor ? (a) Inside positive, outside negative (b) Inside negative, outside positive (c) Both negative (d) Both positive

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 70 views

. If the peak transmitted power in a radar system is increased by a factor of 16, the maximum range will be increased by a factor of : (A) 2 (B) 4 (C) 8 (D) 16

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

If the supply frequency of a 3-phase induction motor is ‘f’, then frequency of rotor emf at motor slip ‘s’ will be   (a) sf (b) (1 – s)f (c) f/s (d) None of these 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

The phase angle corresponding to λ/4 in a standing– wave pattern is: (1) 30° (2) 90° (3) 135° (4) 180°

asked May 28, 2018 in Electronics Engineering by Shimroz123
0 answers 19 views

For applications requiring speed ratio other than 2 : 1, the speed control of an induction motor can be effected by varying the number of stator poles employing  (1) multiple stator winding (2) pole amplitude modulation technique (3) consequent pole technique (4) Any of these

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 37 views

If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

asked Mar 25, 2018 in Basic concepts by Shimroz123
0 answers 76 views

A 3-phase circuit breaker is rated at 1250 A, 2000 MVA, 33 kV, 4s. Its making current capacity will be   (a) 35 kA (b) 89 kA (c) 79 kA (d) 69 kA

asked Apr 10, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...