34 views
in Electrical Measurements and Instrumentation by
A Wien bridge is used to measure (A) quality factor of a coil (B) audio frequency of a signal (C) capacitance of a capacitor (D) inductance of a coil 
by
Capacitance is ryt

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

2 Answers

0 votes
by
Inductance of a coil
0 votes
by
D)  Inductance of a coil

Related questions

2 answers 64 views

The bridge used to measure the dielectric loss of an insulator is: A) Anderson bridge B) Wien’s bridge C) Schering bridge D) Any of the above

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 12 views

Maxwell's bridge is used to measure (A) Inductance (B) Frequency (C) Capacitance (D) Resistance

asked May 13, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 6 views

Schering bridge is used to measure  (1) Frequency (2) Inductance (3) Capacitance (4) Mutual Inductance

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 8 views

Which of the following is true with respect to Wien Bridge? A) It does not require equal values of R or C  B) It requires that R and C values of all components must be equal C) It requires that all resistors should have equal values D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

A dummy strain gage is used in a quarter bridge strain gage circuit to :  (A) compensate for changes in temperature and lead wire resistance  (B) produce more output voltage from the bridge  (C) increase the sensitivity of the bridge  (D) compensate lead wire resistance only

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 9 views

A Wien Bridge Oscillator is suitable for  1. Audio frequency applications 2. Radio frequency applications 3. Very low frequency applications Which of the above frequency applications is/are correct ?

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 137 views

Feedback factor at the frequency of oscillation of a Wien bridge oscillator is:  (1) 3 (2) 1/3 (3) 1/29 (4) 3/29

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

A VTVM can be used to measure (a) dc voltage only (b) ac voltage only (c) both (a) and (b) (d) None of the above 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 106 views

Which of the following can be used to measure the capacitance of a capacitor? A) Rheostat B) Schering bridge C) Wheatstone bridge D) None of these

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 20 views

Megger is used to measure (a) very high resistance or insulation resistance. (b) low resistance. (c) high resistance. (d) very low resistance. 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 18 views

Piezoelectric Transducer is used to measure  (1) displacement (2) resistance (3) current (4) temperature

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 58 views

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
3 answers 90 views

What type of meter is used to measure current?

asked Mar 10, 2018 in Electrical Measurements and Instrumentation by Quiz
2 answers 111 views
1 answer 10 views

Assertion (A) : Wein bridge oscillator is generally used as a variable audio frequency oscillator Reason (R) : by using either capacitor (or) resistor in one of the arms of the bridge, the frequency of a wein bridge oscillator can be varied (A) Both (A) & (R) are true & (R) is correct explanation of (A) (B) Both (A) & (R) are true but (R) is not the correct explanation of (R). (C) (A) is true but (R) is false (D) (A) is false but (R) is true

asked May 24, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 10 views

Moire fringes are used to measure rotary displacement along with _____.

asked May 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 2,714 views

Which of the following instruments can be used to measure AC current only? (a) Permanent Magnet Type ammeter(b) Induction type ammeter (c) Moving iron voltmeter(d) Moving iron ammeter

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 17 views

A d.c. potentiometer is designed to measure up to about 2V with a slide wire of 800 mm. A standard cell of emf 1.18V obtains balance at 600 mm. A test cell is seen to obtain balance at 680 mm. The emf0fthe test cell is  A)1.00V B)1.34V C)1.50V D)1.70V 

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 14 views

A Pyrheliometer is an instrument to measure :  (A) temperature of solar photovoltaic cell  (B) intensity of direct solar radiation at normal incidence  (C) intensity of indirect solar radiation  (D) efficiency of a solar photovoltaic cell

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 21 views

To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that the supply for the potentiometer in taken?

asked Mar 21, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 22 views

For measurement of low resistance, the bridge used is (a) Wheatstone (b) Kelvin (c) Maxwell (d) Anderson

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 22 views

The Maxwell bridge is used for measuring (a) Capacitance (b) Dielectric loss (c) Inductance (d) Phase angle 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 11 views

Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is   (A)sinusoidal (B) square (C) rectangular (D) triangular

asked May 17, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 27 views

The bridge method commonly used for finding mutual inductance is (A) Heaviside Campbell bridge (B) Schering bridge (C) De Sauty bridge (D) Wien bridge

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 23 views

The current transformer that is used to measure a 100 A current by 5 A ammeter is a_____.

asked May 29, 2018 in Transformer by Shimroz123
1 answer 20 views

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 24 views

Which of the following measure(s) is/are used to determine the quality of a printer ___.  a) Dots printed in a minute b) Dots per Inch c) Dot-Per-Square-Inch d) All of the Above

asked May 13, 2018 in Computer Engineering by Shimroz123
1 answer 28 views

A _________ is used to measure the stator % winding temperature of the generator.  (A) Thermocouple (B) Pyrometer (C) Resistance thermometer (D) Thermometer

asked May 8, 2018 in Electrical Machine by Shimroz123
1 answer 27 views

Two wattmeters are used to measure the power in a 3 -phase balanced system. What is the power factor of the load when one wattmeter reads twice the other ?  (a) 0 (b) 0.5 (c) 0.866 (d) 1

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 14 views

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 12 views

The minimum number of wattmeter(s) required to measure 3-phase, 3-wire balanced or unbalanced power is  A) 1 B) 2 C) 3 D) 4

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
5 answers 202 views
1 answer 14 views

Slotted line with tunable probe is not used to measure  a) VSWR b) Wavelength c) Power d) Impedance

asked Jun 15, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

The principle of operation used in capacitive transducers to measure level of liquid is change of (a) Area of plates (b) Dielectric strength (c) Distance between plates (d) Shape of plates

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
2 answers 74 views

What type of instrument is used to measure dc voltage of the order 5 volts? (A) moving iron type (B) electro-static type (C) moving coil type (D) all of these

asked Apr 23, 2018 in Electronics Engineering by Shimroz123
1 answer 41 views

Thermocouple is used to measure : - a) AC b) DC c) Both d) None

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 28 views

CRO is used to measure ________. A. Amplitude B. Phase difference C. Frequency D. All of these 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

133 comments

3,086 users

...