Can you help by answering this question?

Speed of light in air is:....

46 views
in Electric Power Transmission by
A single-line-to-ground fault on a overhead transmission line creates (A) voltage sag (B) voltage swell (C) over voltage (D) voltage flicker 

1 Answer

0 votes
by
Creates  overvoltage.

Related questions

1 answer 25 views

Earth wire on EHV overhead transmission line is provided to protect the line against:

asked May 22, 2018 in Electric Power Transmission by Shimroz123
0 answers 22 views

An overhead transmission line has a span of 260 m. The weight of the conductor is 0.68 kg/m. The maximum allowable tension in the line is 1550 kg. Maximum sag of the line should be (a) 5.8 m (b) 4.6 m (c) 2.7 m (d) 3.7 m 

asked May 25, 2018 in Electric Power Transmission by Shimroz123
0 answers 91 views

The presence of earth in case of overhead transmission line (a) increases capacitance (b) increases inductance (c) decreases capacitance (d) decreases inductance

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 40 views

Effect of increase in temperature in an overhead transmission line is (a) to increase stress and length both (b) to decrease stress and length both (c) to decrease stress and increase length (d) None of the above 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 20 views

The zero sequence current of a generator for line to ground fault is j 2.4 p.u. The current through the neutral during the fault is (a) j 0.8 p.u (b) j 2.4 p.u. (c) j 0.24 p.u. (d) j 7.2 p.u. 

asked May 25, 2018 in Power system by Shimroz123
1 answer 29 views

If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) zero sequence currents are absent on both sides of the transformer  (C) zero sequence currents are present on the secondary side but not on the primary side  (D) zero sequence currents are present on the primary side but not on the secondary side

asked Apr 29, 2018 in Power system by Shimroz123
0 answers 26 views

When a line -to -ground fault occurs, the current in a faulted phase is 100A. The negative sequence current in this case will be : (A) Zero (B) 33.3 A (C) 66.6 A (D) 100 A

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

The power loss in a transmission line depends on (a) current in the line. (b) resistance of the line. (c) length of the line. (d) All of the above 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 89 views

A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

asked May 3, 2018 in Electric Power Transmission by Shimroz123
1 answer 40 views

The inductance of single phase two wire power transmission line per km gets doubled when the  (a) Distance between wires is doubled  (b) Distance between the wires is increased four fold  (c) Distance between the wires is increased as square of the original distance  (d) Radius of the wire is doubled

asked May 13, 2018 in Electric Power Transmission by Shimroz123
1 answer 19 views

The time taken for a surge to travel a 600 km long overhead transmission line is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 30 views

The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?

asked Mar 20, 2018 in Induction Machine by Shimroz123
0 answers 19 views

A transmission line to be reciprocal, the condition is (a) A = D (b) AC – BD = 1 (c) AD – BC = 1 (d) AB – CD = 1  

asked May 25, 2018 in Electric Power Transmission by Shimroz123
1 answer 26 views

To increase power transfer capability of a long transmission line, we should:  (1) Increase line resistance (2) Increase transmission voltage (3) Decrease line reactance (4) Both (2) & (3)

asked May 22, 2018 in Electric Power Transmission by Shimroz123
1 answer 115 views

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line 

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 22 views

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 51 views

For a single phase overhead line having solid copper conductors of diameter 1 cm, spaced 60 cm between centers, the inductance in mH/km is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 17 views

A long overhead transmission line is terminated by its characteristic impedance. Under this operating condition, the ratio of the voltage to the current at different points along the line will?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 16 views

An overhead transmission line has a span of 240m between level supports. What is the maximum sag if the conductor weight 727 kg/km and has a breaking strength of 6880 kg? Allow the factor of safety of 2. Neglecting wind and ice loading.

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 32 views

In an AC transmission line difference in phase of voltage at two ends of the line is due to (a) System voltage (b) Insulators (c) Resistance of line (d) Reactance of line

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 20 views

What type of insulator will be used if the direction of the transmission line is to be changed?

asked May 22, 2018 in Electric Power Transmission by Shimroz123
1 answer 79 views

Galloping in transmission line conductors arises generally due to - (A) asymmetrical layer of ice formation (B) vortex phenomenon in light winds (C) heavy weight of line conductors (D) adoption of horizontal conductor

asked May 13, 2018 in Electric Power Transmission by Shimroz123
0 answers 26 views

Using the F11 shortcut key to create a chart on chart sheet creates  (1) A default chart (2) A 2-dimensional column chart (3) A 2-dimensional bar chart (4) A 3-dimensional line chart

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 12 views

When the load on a transmission line is equal to the surge impedance loading  (a) The receiving end voltage is less than the sending end voltage  (b) The sending end voltage is less than the receiving end voltage  (c) The receiving end voltage is more than the sending end voltage  (d) The receiving end voltage equal to the sending end voltage 

asked May 13, 2018 in Electrical Engineering by Shimroz123
2 answers 48 views

A long transmission line has considerable ……………….. effect. A) series capacitance B) shunt capacitance C) series inductance D) shunt inductance

asked Jun 4, 2018 in Electric Power Transmission by Shimroz123
1 answer 30 views

For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic impedance is: (1) 100 Ω (2) 50 Ω (3) 25 Ω (4) 10 Ω

asked May 29, 2018 in Electric Power Transmission by Shimroz123
0 answers 20 views

If diameter of each conductor of a transmission line is ‘d’, then the diameter of n-layer stranded conductor will be (a) (2n – 1) d (b) (2n + 1) d (c) (3n – 1) d (d) (3n + 1) d 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 12 views

The input impedance of a short circuited loss less transmission line of characteristic impedance 50 Ohm is

asked May 23, 2018 in Electric Power Transmission by Shimroz123
1 answer 27 views

The inductance of a power transmission line increases with (A) decrease in line length. (B) increase in conductor diameter. (C) increase in spacing between phase conductors. (D) increase in load current carried by conductors.

asked May 13, 2018 in Electric Power Transmission by Shimroz123
1 answer 30 views

Stability of a transmission line can be increased by

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 21 views

Surge impedance of overhead transmission line is normally in the order of (a) 1- 5 ohms (c) 300 - 500 ohms (b) 20 - 30 ohms (d) 300000 - 500000 ohms

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

In terms of cost, overhead transmission line is better than underground transmission line in the field of   (a) Insulation (b) Right of way (c) Visibility (d) None of these 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 50 views

A single phase transmission line and a telephone line are both symmetrically strung one below the other, in horizontal configurations, on a common tower, The shortest and longest distances between the phase and telephone conductors are 2.5 m and 3 m respectively. The voltage (volt/km) induced in the telephone circuit, due to 50 Hz current of 100 amps in the power circuit is (A) 4.81 (B) 3.56 (C) 2.29 (D) 1.27

asked May 25, 2018 in Power system by Shimroz123
1 answer 16 views

 A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 31 views

A voltage of 1000 kV is applied to an overhead line with its receiving end open. If the surge impedance of the line is 500 ohm, then the total surge power in the line ill

asked Mar 27, 2018 in Power system by Shimroz123
0 answers 26 views

Which of the following relations is true for long transmission line ? (a) VS = AVR – BIR (b) VS = BVR + AIR (c) VS = AVR + BIR (d) VS = BVR – AIR

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 25 views

Which of the following is used for power factor improvement in transmission line ? (a) Three phase induction (b) An overexcited three phase synchronous motor running on no load (c) Three phase AC series motor (d) Choke

asked May 26, 2018 in Electric Power Transmission by Shimroz123
0 answers 16 views

The bundled conductor in EHV transmission line system provides (a) increased inductance (b) reduced capacitance (c) increased capacitance (d) increased voltage gradient

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 380 views

The main consideration for operating transmission line at high voltage is (a) to increase efficiency only. (b) to reduce power loss only. (c) to increase power transmission capability only. (d) All of the above

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 20 views

Why are shunt reactors connected at the receiving end of long transmission line system: (1) To increase the terminal voltage (2) To compensate voltage rise caused by capacitive charging at light load (3) To improve power factor (4) None of these

asked May 22, 2018 in Electric Power Transmission by Shimroz123
1 answer 55 views

How many insulator disc used for 33 kV transmission voltage line?

asked Dec 5, 2017 in Electric Power Transmission by Quiz
1 answer 79 views

how the booster is connected in transmission line ?

asked Aug 18, 2017 in Electric Power Transmission by Zeeshan
1 answer 50 views

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 13 views

A travelling wave of surge resistance, Ro on a transmission line is terminated by a load resistance, RL. If RL > Ro then there is (A) no reflected wave (B) partial reflection of reversal of current only (C) partial reflection of reversal of voltage only (D) reflection of reversal of both current and voltage

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

Bundled conductors are mainly used in high voltage overhead transmission lines to (a) Reduce line loss (c) Reduce corona (b) Reduce harmonics (d) Increase strength

asked Apr 25, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...