Ask a Question
Full load copper loss in a transformer is 1600 watts. At half load the copper loss will be:
Full load copper loss in a transformer is 1600 watts. At half load the copper loss will be: A) 6400 watt B) 1600 watt C) 800 watt D) 400 watt
Jun 4, 2018
to add a comment.
← Prev Question
Next Question →
to answer this question.
Full load cupper loss in a transformer is 1600 watts. At half load the cupper loss will be:
Jun 17, 2018
to add a comment.
The full-load copper loss of a transformer is 1600 W At half-load, the copper loss will be?
A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -
At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total
The eddy current loss in an AC motor is 100 watts at 50 Hz. Its losses at 100 Hz will be:
A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The
A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage
What is the efficiency of this transformer on full and half load.
In an actual transformer the iron loss remains practically constant from no load to full load because?
In a transformer, zero voltage regulation at full load is
What will be the efficiency when the transformer operates at unity power factor and 60% of full load
In a transformer the voltage regulation will be zero when it operates at
A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at
A single-phase, 50 kVA, 250 V/500 V two winding transformer has an efficiency of 95% at full load, unity
The power in a series R-L- C circuit will be half of that at resonance when the magnitude of the current is equal to
The r.m.s. value of a half-wave rectified alternating current is 10 A. Its value for full-wave rectification will be
An ideal transformer will have maximum efficiency at a load such that?
For a transformer, operating at constant load current, maximum efficiency will occur at?
If the supply frequency to the transformer is increased, the iron loss will?
In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at
In a d.c. series motor, the torque developed is 20 Nm at 10A. If the load current is doubled, the new torque will be : -
The efficiency of a transformer at full load 0.8 p.f lagging is 90%. Its efficiency at full load 0.8 p.f...
A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit
The no-load current drawn by transformer is usually what per cent of the full-load current ?
A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the
A 220 V D.C. generator is run at full speed without any excitation. The open circuit voltage will be?
In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary
Iron loss of a transformer can be measured by?
A transformer operates 24 hours day at full -load. It's full -load efficiency is :
One 200 KVA transformer has an iron loss of 1 KW and full load Cu loss of 2 KW. Its load KVA corresponding...
Even at no-load, a transformer draws current from the mains. Why?
When secondary of a current transformer is open-circuited its iron core will be?
An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW.
If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?
A two -winding single phase transformer has a voltage regulation of 4.5% at full - load and unity power ...
If a transformer is continuously operated the maximum temperature rise will occur in?
For a constant load current, transformer maximum efficiency occurs at
The voltage applied to the H.V. side of a transformer during S.C. test is 2% of the rated voltage. The core loss
A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the
In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?
As we know when there is a joint in optical fiber then there will be some loss then this loss be minimized by
A single phase full -wave half controlled bridge converter feeds an inductive load:
A 150 kW electric motor has an efficiency of 92 %, when it operates at full load. Calculate the losses in the...
Using a quarter wave transformer of characteristic impedance 1 Ohms, a load impedance of 100 Ohms will be...
The no load current in a transformer lags behind the applied voltage by an angle of about?
Auto-transformer makes effective saving on copper and copper losses, when its transformation ratio is?
A single phase 230 V/ 150 V , 1 kVA, 50 Hz transformer is supplied by 230 V AC supply. Find the full load primary and secondary current.
The efficiency of a 3-phase, star connected synchronous motor is 95% and it takes 24A at full load
The constant of a given energy meter is 500 revolution/kWh. At the test 4.4 kW full load, meter completes 50
A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for
The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main...