Can you help by answering this question?

What is a Ductor tester used for?

15 views
in Maximum Power Transfer theorem by
For AC networks, as per maximum power transfer theorem, for maximum power transfer, the source impedance should be equal to: A) twice the load impedance B) complex conjugate of load impedance C) twice the complex conjugate of load impedance D) none of these 

2 Answers

–1 vote
by
Load impedance must be complex conjugate of source impedance
0 votes
by

 For AC networks, as per maximum power transfer theorem, for maximum power transfer, the source impedance should be equal to: complex conjugate of load impedance

Related questions

1 answer 12 views

State maximum power transfer theorem for DC circuit.

asked Sep 6, 2018 by Shimroz123
1 answer 26 views

For maximum transfer of power, internal resistance of the source should be?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 26 views

Maximum Power Transfer Theorem 1

asked May 22 by Shimroz123
1 answer 51 views

In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 29 views

For high efficiency of transfer of power, internal resistance of the source should be?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 37 views

As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by (symbols/notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 21 views

An 800 kV transmission line has a maximum power transfer capacity of P. If it is operated at 400 kV with the series reactance unchanged, the new maximum power transfer capacity is approximately (A) P (B) 2P (C) P / 2 (D) P / 4

asked May 25, 2018 in Power system by Shimroz123
1 answer 44 views

In an alternator at lagging power factor the generated voltage per phase as compared to that at unity power factor?

asked Mar 18, 2018 in Alternator by Shimroz123
1 answer 17 views

When a source is delivering maximum power to a load, the efficiency of the circuit is always (a) 50% (b) 75% (c) 100% (d) Depends on the circuit parameters

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 12 views

Give the criteria for selection of distribution transformer as per IS:10028 (part-I) 1985.

asked Sep 18, 2018 by Shimroz123
1 answer 12 views

The color of wire recommended for earth connection as per BIS code is

asked May 14, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

How many characters per sec (7 bits + 1 parity) can be transmitted over a 2400 bps line if the transfer is synchronous (1 start bit and 1 stop bit)?  A) 300 B) 240 C) 250 D) 275

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 72 views

 An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
0 answers 6 views

Two two-port networks are connected in cascade. The combination is to be represented as a single two-port network. The parameters of the network are obtained by multiplying the individual a. z-parameter matrix b. h-parameter matrix c. y-parameter matrix d. ABCD-parameter matrix

asked May 24, 2018 in Network Analysis by Shimroz123
1 answer 8 views

As per Electricity Act, ____________means any line which is used for carrying electricity for any purpose.  (A) Electric line (B) Transmission line (C) All of the above (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor is   (A) square wave (B) triangular wave (C) step function (D) pulsed wave

asked May 17, 2018 in Power electronics converters by Shimroz123
0 answers 39 views

For a transient stability analysis, as long as equal area criterion is satisfied, the maximum angle to which rotor angle can oscillate is:  (A) 0˚ to 20˚ (B) 45˚ to 50˚ (C) Greater than 90˚ (D) 65˚ to 85˚

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 30 views

Why superposition theorem is not valid for power?

asked Mar 10, 2018 in Electrical Engineering by Quiz
0 answers 24 views

Can we apply the superposition theorem to AC circuit?

asked Mar 10, 2018 in Electrical Engineering by Quiz
1 answer 26 views

An iron cored inductance coil can be modelled, over a normal operating range of networks ,as A) non-Linear bilateral element B) linear bilateral element C) linear time varying element D) non-linear time invariant element

asked May 24, 2018 in Electrical Engineering by Shimroz123
0 answers 45 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 15 views

What is the maximum value of a load which consume 500 KWh per day at a load factor of 0.40, if the consumer increases the load factor of 0.50 without increasing the maximum demand? 

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 8 views

For a series R -C circuit, the power factor corresponding to maximum power is (a) 0-5 lag (b) 0.5 lead (c) 0.707 lag (d) 0-707 lead

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
2 answers 73 views

The maximum power in a synchronous motor (for a given excitation) is produced when the power angle is equal to: (A) 0° (B) 45° (C) 60° (D) 90°

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 3 views

For very low speed and high power applications the best suited ac motor is:

asked May 22, 2018 in Electrical Machine by Shimroz123
0 answers 45 views

What is the symbol for AC power?

asked Mar 11, 2018 in Electrical Engineering by Quiz
1 answer 35 views

The superposition theorem requires as many circuits to be solved as there are?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 22 views

Can you apply Thevenin's theorem in an AC circuit?

asked Mar 10, 2018 in Electrical Engineering by Quiz
0 answers 24 views

Can we apply Norton's theorem in an AC circuit?

asked Mar 10, 2018 in Electrical Engineering by Quiz
1 answer 27 views

In dc choppers per unit ripple is maximum when duty cycle is   (a) 0.2 (b) 0.5 (c) 0.7 (d) 0.9

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 25 views

Give the specification of three phase transformer as per IS 1180(Part-1) 1989. 

asked Sep 18, 2018 by Shimroz123
1 answer 18 views

 Gauge factor of strain gauge is defined as the ratio of per unit change in the ______.

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

The number of processes completed per unit time is known as ____________. (A) output (B) throughput (C) efficiency (D) capacity

asked Apr 23, 2018 in Computer Engineering by Shimroz123
0 answers 31 views

The number of processes completed per unit time is known as __________.  (1) Output (2) Throughput (3) Efficiency (4) Capacity

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 12 views

 For rural electrification in a country like India with complex networks, it is preferable to use: A) Air circuit breaker B) Oil circuit breaker C) Vacuum circuit breaker D) Minimum oil circuit breaker

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

For large networks, which topology is used  (1) Bus (2) Star (3) Ring (4) Mesh

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 15 views

In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output. This inductance maintains a ……… …………through the switching devices over short interval of time. A) constant current B) constant voltage C) constant power D) none of the (A), (B), (C)

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

An R-L series AC circuit has R = 10 ohm and XL = 10 ohm. It is connected to an AC voltage source, the phase angle between voltage and current is (a) 30° (b) 45° (c) 60° (d) 36.8°

asked May 25, 2018 in Network Analysis by Shimroz123
1 answer 17 views

The transient current in lossless L-C circuit when excited from an AC source is, sine wave  (a) Critically damped (b) Underdamped (c) Overdamped (d) Undamped

asked May 16, 2018 in Electronics Engineering by Shimroz123
1 answer 24 views

The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

asked May 15, 2018 in Basic concepts by Zeeshan
1 answer 33 views

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter (b) Fully controlled bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The two basic components of a Thevenin equivalent ac circuit are the equivalent voltage source and the equivalent: A. Series impedance B. Series resistance C. Parallel impedance D. Parallel resistance

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

_______ electric power is the most common method used by electrical grids to transfer power.  (A) One-phase (B) Two-phase (C) Three-phase (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 54 views

The reactive power transfer over a line mainly depends on

asked Apr 27, 2018 in Switchgear And Protection by Shimroz123
1 answer 40 views

The inductance of single phase two wire power transmission line per km gets doubled when the  (a) Distance between wires is doubled  (b) Distance between the wires is increased four fold  (c) Distance between the wires is increased as square of the original distance  (d) Radius of the wire is doubled

asked May 13, 2018 in Electric Power Transmission by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...