# In axial flow fans and turbines, fluid enters and leaves as follows :

42 views
In axial flow fans and turbines, fluid enters and leaves as follows : (A) radially, axially (B) axially, radially (C) axially, axially (D) radially, radially

In axial flow fans and turbines, fluid enters and leaves as follows : (A) radially, axially (B) axially, radially (C) axially, axially (D) radially, radially

## Related questions

A fluid in equilibrium cannot sustain : (A) tensile stress (B) compressive stress (C) shear stress (D) bending stress

Angle between the shear plane and work surface is known as : (A) lip angle (B) rake angle (C) cutting angle (D) shear angle

In case of load flow analysis one of the system buses is taken as swing bus (a) as reference bus (b) to compensate the system losses (c) both (a) and (b) (d) to reduce the system losses

In load flow Study, a PV bus is treated as a PQ bus when

In load flow analysis, the load connected at a bus is represented as?

Consider the following statements :  1. Salient pole alternators have small diameters and large axial lengths.  2. Cylindrical rotor alternators have a distributed winding.  3. Cylindrical rotor alternators are wound for large number of poles.  4. Salient pole alternators run at speeds slower than cylindrical rotor machines.  Which of the above statements are correct ?  (a) 1 and 3 only (b) 2 and 4 only (c) 1 and 4 only (d) 2 and 3 only

In the thermal power plants, the pressure in the working fluid cycle is developed by  (A) condenser (B) super heater (C) feed water pump (D) turbine

List out the energy conservation techniques in Fans.

The usual ratio of forward and return stroke in shaper is : (A) 2:1 (B) 1:2 (C) 2:3 (D) 3:2

In a Traveling-wave Tube, the velocity of electron beam with respect to the axial velocity of RF field is kept...  A) Lower B) Higher C) Equal D) Any of these

In an axial mode operation of a helical antenna, maximum field radiated by the antenna is :  A) along the axis of the helical B) in a plane normal to the helix antenna axis C) in both axial and normal planes D) None of the above

Dew point temperature is constant as long as there is : (A) no change in moisture content of the air (B) no change in volume of air (C) no change in dry bulb and wet bulb temperature (D) no change in relative and specific humidity of air

Military type of organisation is known as : (A) line organisation (B) functional organisation (C) line and staff organisation (D) line, staff and functional organisation

The ratio of maximum displacement of the forced vibration to the deflection due to static force is known as : (A) Damping Factor (B) Damping Coefficient (C) Logarithmic Decrement (D) Magnification Factor

A casting defect which occurs near the ingates as rough lumps on the surface of a casting is known as 1. Shift 2. Sand wash 3. Swell 4. Scab

Structural sections such as rails, angles, I-beams are made by 1. Hot rolling 2. Hot drawing 3. Hot piercing 4. Hot extrusion

What is the purpose of the turbines in coal fired power plants?

Is it true or false that electron flow and conventional current are in opposite directions?

Classify hydro-electric power plants according to water flow regulation and explain in brief.

If the reference bus is changed in two load flow runs with same system data and power obtained for reference bus taken as specified P and Q in the latter run, the system losses  A) Will be unchanged but complex bus voltages will change B) Will change but complex bus voltage remain unchanged C) As well as complex bus voltage will changed D) As well as complex bus voltage will be unchanged

For a fixed value of complex power flow in a transmission line having a sending and voltage V, the real power loss will be proportional to  A) V B) v2 C) 1/V2 D)1/V

An electron having an energy of 20 eV enters a magnetic field of 0.02 webers/sqm at an angle of 30degrees to the field. The time of travel (in nS)of the electron for one revolution is about  A) 1.78 B) 4.21 C) 7.82 D) 10.24

A d.c. motor can be looked upon as d.c. generator with the power flow?

Induced draft fans are located at:

A d.c. shunt motor is found suitable to drive fans because they require?

If a shaft made of ductile material is subjected to combined bending and twisting moments, calculation based on which one of the following theories would give the most conservative values ? (A) Maximum principle stress theory (B) Maximum shear stress theory (C) Maximum strain energy theory (D) Maximum distortion energy theory

The process extensively used for making bolts and nuts is 1. Hot piercing 2. Extrusion 3. Cold peening 4. Cold heading

Main advantage of fiber optic cable over co-axial cable is

State the types of wind turbines.

Kaplan turbines are used whenever the water head is (a) low (b) high (c) medium (d) (b) and (c)

Transient stability can be improved by using governors attached to the turbines, should be (a) fast acting (b) slow acting (c) no function of governors in improving stability (d) nothing can be said

The transfer of energy for reaction turbines is based on _______ A) Newton’s first law B) Newton’s second law C) Newton’s third law D) All the above

The efficiency of modern steam turbines is about (1) 50% (2) 85% (3) 75% (4) 90%

The comfort conditions in air conditioning are : (A) 22 ºC dry bulb temperature and 60% relative humidity (B) 25 ºC dry bulb temperature and 100% relative humidity (C) 20º C dry bulb temperature and 75% relative humidity (D) 15º C bulb temperature and 80% relative humidity

In inventory control theory, the economic order quantity is : (A) average level of inventory (B) optimum lot size (C) capacity of a warehouse (D) lost size corresponding to break-even analysis

In value engineering, the term value refers to : (A) manufacturing cost of the product (B) selling price of the product (C) total cost of the product (D) utility of the product

Binding material used in cemented carbide tools is : (A) Nickel (B) Cobalt (C) Chromium (D) Silicon

In a clock mechanism, the gear train used to connect minute hand to hour hand, is : (A) Epicyclic gear train (B) Reverted gear train (C) Compound gear train (D) Simple gear train

Two metallic blocks having masses in the ratio 2:3 are made to slide down a frictionless inclined plane starting from rest position. When the blocks reach the bottom of the inclined plane, they will have their kinetic energies in the ratio : (A) 2:3 (B) 3:5 (C) 3:2 (D) 7:4

In die casting, machining allowance is 1. Small 2. Large 3. Very large 4. Not provided

Explain the difference between electron flow and conventional current.

Draw and explain power flow diagram of induction motor.

Which type of flow is measured by hot wire anemometer and describe its working principle with suitable diagram.

Draw and explain the working principle of turbine type flow meter. Mention its Application area.

Differentiate between mass flow rate and volumetric flow rate.