Can you help by answering this question?

The type of phospher used in CRT used for television is...

29 views
in Switchgear And Protection by
The burden value in Potential Transformer (PT) should be ______ to achieve low errors in PT: A) low B) high C) medium D) infinite

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

The burden value in Potential Transformer (PT) should be high to achieve low errors in PT: 

Related questions

1 answer 26 views

For selecting a circuit breaker, ______ should be determined.  (A) initial current that flows on occurrence of a short circuit only (B) transient current that flows at the time of circuit interruption only (C) resonant frequency only (D) (A) and (B) 

asked Apr 30, 2018 in Switchgear And Protection by Shimroz123
1 answer 39 views

The burden of protective Current Transformer (CT) is specified in

asked May 15, 2018 in Switchgear And Protection by Shimroz123
1 answer 16 views

Mention the precautions to be taken while connecting CT and PT in the circuit. 

asked Sep 6, 2018 by Shimroz123
0 answers 16 views

In an instrument transformer the errors can be reduced by  (A) Using high reluctance core (B) Using small cross sectional area (C) Using low permeability materials (D) Using low reluctance core 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 391 views

In which of the following transmission lines, the value of the Shunt admittance should be approximated to zero ? (A) A 66 kV 35 km long line (B) A 132 kV 200 km long line (C) A 220 kV 300 km long line (D) A 400 kV 500 km long line

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 19 views

State any four periodical maintenance which is necessary in transformer to achieve energy conservation.

asked Sep 22, 2018 in Energy Conservation And Audit by Shimroz123
1 answer 28 views

In a synchronous generator if the excitation increased from a low value to normal value, with a fixed load  (A) The armature current increases and the power factor decreases  (B) The armature current decreases and the power factor also decreases  (C) The armature current decreases and the power factor increases but is lagging  (D) The armature current decreases and the power factor increases and is leading

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 20 views

In a transformer the resistance between its primary and secondary should be?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 8 views

If MN/MX is low the 8086 operates in  ______ mode.   (a) Minimum (b) Maximum (c) Minimum & Maximum (d) Medium 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

What should be the value of earthing resistance for large power stations?

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

The four stripes of a resistor are yellow-violet-orange-gold. The value of resistor should be A. 470 ohms ± 5 % B. 47 kilo ohm ± 5% C. 47 mega ohms ± 5% D. 4700 ohms ± 10%. 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

For proper earthing, what should be the maximum value of earth resistance while carrying out the testing of earth continuity path ?   (a) 1 Ω (b) 2 Ω (c) 5 Ω (d) 10 Ω 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

What should be kVA rating of each transformer in V-V bank when three phase balanced load is 40 kVA ? (A) 19 (B) 28 (C) 37 (D) 23

asked May 13, 2018 in Electrical Engineering by Shimroz123
2 answers 57 views

An Auto-transformer (which has only one winding) may be used as a ______ .  (A) Both Step-Up and Step-Down transformer (B) Step-Down Transformer (C) Step-Up Transformer (D) None of these

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

For an antenna to be frequency-independent, it should expand or contract in proportion to the  (a) gain (b) directivity (c) wavelength (d) impedance

asked May 15, 2018 in Electronics communication by Zeeshan
1 answer 17 views

In a single phase induction motor driving a fan load, the reason for having a high resistance rotor is to achieve (A) low starting torque (B) quick acceleration (C) high efficiency (D) reduced size

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 24 views

An A.C current is given by i=100sin100. It will achieve a value of 50 A after (1) 1/600 sec (2) 1/300 sec (3) 1/1800 sec (4) 1/900 sec 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

When the phase difference between two sinusoidal quantities is 90° they are said to be ______ A) Phase right angle B) Phase quadrature C) Phase sinuright D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Materials, whose resistivity at very low temperatures plunges from a finite value to zero and remains there upon further cooling, are known as

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The low voltage winding of a 400/230 V, 1-phase, 50 Hz transformer is to be connected to a 25 Hz, the supply voltage should be

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 34 views

For a traction transformer circuit breaker state: 1) Rated current and rupturing capacity 2) Any two tests it should be capable of withstanding 3) Overall tripping time and relay time.

asked Sep 2, 2018 by Shimroz123
1 answer 49 views

In an AC. circuit, a low value of kVAR compared with kW indicates?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In a transformer, low voltage winding is placed near the core in case of concentric windings so as to  1. Reduce the leakage flux 2. Reduce the insulation requirement 3. Reduce the risk of voltage shock in case of insulation breakdown 4. Reduce the core loss   From these, the correct answer is (a) 1, 2, 3 (b) 2, 3, 4 (c) 1, 2, 3, 4 (d) 2, 3

asked May 13, 2018 in Transformer by Shimroz123
0 answers 13 views

Transient stability can be improved by using governors attached to the turbines, should be (a) fast acting (b) slow acting (c) no function of governors in improving stability (d) nothing can be said  

asked May 25, 2018 in Power system by Shimroz123
1 answer 17 views

To turn a UJT ON, the forward bias on emitter diode should be:  1. more than the peak point voltage 2. less than the peak point voltage 3. Equal to the peak point voltage 4. Equal to the stand - off voltage  

asked May 13, 2018 in Power Electronics by Shimroz123
0 answers 58 views

To enable dc series motor work satisfactory with an AC supply, the following modifications should be done (1) The yoke and poles should be completely laminated (2) The poles should be made of laminated steel (3) The air gap between stator and rotor be reduced (4) Compensating poles should be introduced  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A megger is to measure insulation resistance of a cable. The cable should be connected to   (a) Battery (b) DC supply (c) AC supply (d) No supply  

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

500 Bytes of data needs to be transmitted from an UART every lOOms. What should be the minimum transmission baud rate of UART, assuming 1 start bit, 8 data bits and 2 stop bits?  A) 50000 B) 55000 C) 40000 D) 45000

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

The path of magnetic flux in a transformer should have?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 8 views

State the effects of errors in dynamometer type wattmeter due to i) pc- inductance ii) pc- capacitance iii) mutual inductance iv) Connection.

asked Sep 6, 2018 by Shimroz123
1 answer 10 views

What arc the errors occurring in measuring devices due to stray magnetic field and temp '? Explain how to compensate them.

asked Sep 6, 2018 by Shimroz123
1 answer 14 views

 The main sources of Errors in Permanent Magnet moving Coil (PMMC) are due to : - a) weaking of the permanent magnet due to aging at temperature effects b) weaking of spring due to aging and temperature effects c) change of resistance of the moving coil with temperature d) all the above

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 14 views

A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is

asked May 14, 2018 in Diode by Shimroz123
1 answer 13 views

When an alternating potential is applied to a capacitor, the current in the circuit will  1. lead the applied potential 2. lag the applied potential 3. be in phase with the applied potential 4. none 

asked May 13, 2018 in Electrical Engineering by Shimroz123
0 answers 14 views

Velocity of an electron (in km/S) starting at rest and travelling to a point 100 V above the starting potential is around  A) 3600 B) 4000 C) 5100 D) 6000

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 25 views

IDMT relays are used to protect the transformer against :  (A) Internal short -circuits (B) Open circuits (C) External short circuits (D) Oil leakage

asked Apr 30, 2018 in Switchgear And Protection by Shimroz123
1 answer 40 views

To prevent mal-operation of differentially connected relay while energizing a transformer, the relay restraining coil is based with  (1) second harmonic current  (2) third harmonic current  (3) fifth harmonic current  (4) seventh harmonic current

asked Apr 29, 2018 in Switchgear And Protection by Shimroz123
1 answer 87 views

To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

asked Apr 27, 2018 in Switchgear And Protection by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,530 questions

7,129 answers

135 comments

3,090 users

...