Can you help by answering this question?

VSWR of a transmission line is always

27 views
in Electronics Engineering by
The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is A) 50 W B) 66 W C) 68 W D) 70 W 

1 Answer

0 votes
by

The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is 66 W

Related questions

0 answers 32 views

 AM transmitter has a carrier power of 30 W. The percentage of modulation is 85%. Calculate the total power : (A) 5.4 W (B) 40.8 W (C) 10.8 W (D) 20.4 W

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 48 views

Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly:  (1) 8.24 KW (2) 9.26 KW (3) 8.47 KW (4) 9.6 KW

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 19 views

Two transformers A and B having equal outputs and voltage ratios but unequal percentage impedances of 4 and 2 are operating in parallel. The transformer A will be overloaded by 

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be (A) 50.55 (B) 15.55 (C) 10.66 (D) 66.66

asked May 12, 2018 in Computer Engineering by Shimroz123
1 answer 8 views

What is the percentage error when 3 resistors with ratings 100 Ω at 5%, 150 Ω at 6% and 250 Ω at 8% respectively, are connected in series? A) 6.33% B) 6.80% C) 19% D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

True value has been 50 whereas measured value is 40 then the percentage error in the reading will be ______.  (A) 20% (B) 40% (C) 50% (D) 30%

asked May 8, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 33 views

What is the percentage of stray losses in DC machine?

asked Mar 8, 2018 in Electronics Engineering by Quiz
0 answers 57 views

What is the working principle of pressure transmitter?

asked Mar 11, 2018 in Transducers and sensors by Quiz
2 answers 46 views

How to find total impedance Z, current I and Impedance angle ?

asked May 30 by Shimroz123
0 answers 33 views

A carrier signal of 600 V rms with 75% amplitude modulation is applied to 75 ohm antenna. The total side band power (in watts) is  A) 4800 B) 450 C) 950 D) 1350 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 44 views

Explain the pulse width modulation technique for control of AC output voltage.

asked Mar 10, 2018 in Power Electronics by Quiz
0 answers 13 views

Explain the significance of over modulation.

asked Mar 10, 2018 in Power Electronics by Quiz
0 answers 1,386 views

In an amplitude modulated system if the total power is 600W and the power in the carrier is 400W, the modulation index is  a. -0.5 b. 0.75 c. 0.9 d. l

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 22 views

What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
2 answers 35 views

What is channel length modulation in MOSFET?

asked Mar 19, 2018 in MOSFET by Quiz
1 answer 46 views

A waveguide termination having VSWR of 1.1 is used to dissipate 100 watts of power. The reflected power will be A) 0.2268 W B) 0.5868 W C) 0.3468 W D) 0.4568 W 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 83 views

The input of an A.C. circuit having power factor of 0.8 lagging is 40 kVA The power drawn by the circuit is?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 57 views

 If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is the transmitter from the target? A) 150 Km B) 150 m C) 15 Km D) 1500 m 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is (A) 0.25 pu (B) 0.5 pu (C) 1.0 pu (D) 1.5 pu

asked Apr 28, 2018 in Electrical Machine by Shimroz123
1 answer 17 views

A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: A. 8.57% B. 42.85% C. 4.28% D. 85.7%

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 41 views

At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
0 answers 12 views

 For identical total transmitted power, the ratio of S/N for wide band FM to S/N of DSB-AM (with ma=1) is : ( Given fm = 15 KHz & frequency. deviation =+/- 75 KHz) a. 112.5 b. 300 c. 75 d. 450

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 23 views

A Power system has a total load of 1260 MW at 50 Hz. The load varies 1.5% for every 1% change in frequency. Find the steady state frequency deviation, when a 60 MW load is suddenly dripped if there is no speed control.  (A) 1.667 Hz (B) 50 Hz (C) No change (D) 3.32 Hz 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

If modulation index is 0.6, maximum power efficiency (in %) of AM is about  A) 60 B) 30 C) 20 D) 10

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 16 views

A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, having a flux of 0.4 mWb and total number of conductors 1000. The value of e.m.f. will be:  (A) 100 Volts (B) 0.1 Volts (C) 1 Volts (D) 10 Volts

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 35 views

What would be the total power drawn from the supply, when two heaters, rated at 1000 W, 250 V each are connected in series across a 250 V, 50 Hz supply?  (A) 1000 W (B) 500 W (C) 250 W (D) 2000 W

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

The resolving power of a spectrometer consisting of collimator, a grating and a telescope can be increased by (A) increasing the angular magnification of the telescope (B) increasing the period of the grating (C) decreasing the period of the grating (D) decreasing the slit-width of the collimator

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 24 views

A transformer at 25 Hz develops 20 W hysteresis loss and 50 W eddy current loss. If the applied voltage and frequency are doubled, the new core losses are (A) 140 W (B) 180 W (C) 240 W (D) 480 W

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

For an earth station transmitter, with an antenna output power of 40dBW 10,000W, a back-off loss of 3dB, a total branching and feeder loss of 3dB, a total branching and feeder loss of 3dB and transmit antenna gain of 4dB, the effective isotropic radiated power (EIRP will be  a) 38dBW b) 40 dBW c 36 dBW d) 47 dBW

asked Jun 15, 2018 in Electronics Engineering by Shimroz123
0 answers 13 views

AM transmitter operating below about 5 MHz usually make use of  A) Marconi antenna B) Turnstile antenna C) Hertz dipole D) Folded dipole 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 13 views

A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is  (A) 50.0% (B) 70.7% (C) 141.4% (D) 200.0%

asked May 17, 2018 in Transformer by Shimroz123
1 answer 25 views

An _____________is a network of electrical components used to supply, transfer and use electric power:  (A) Electric power system (B) Electric power (C) All of the above (D) None of the above

asked May 8, 2018 in Power system by Shimroz123
1 answer 97 views

The apparent power drawn by an A.C. circuit is 10 kVA and active power is 8 kW. The reactive power in the circuit is?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

One advantage of AM over suppressed carrier AM is  A) Less power B) Less bandwidth C) Simpler detection D) Higher efficiency

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 44 views

In an alternator at lagging power factor the generated voltage per phase as compared to that at unity power factor?

asked Mar 18, 2018 in Alternator by Shimroz123
1 answer 22 views

The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 41 views

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 73 views

What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to a 500 Hz (frequency) source of the same voltage:  (A) Eddy Current and Hysteresis losses will be excessive  (B) Current will be too much high  (C) Transformer may start to smoke and burn  (D) No effect

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 35 views

For a 500 Hz frequency excitation, a 50 km long power line will be modeled as

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 36 views

The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: -  a) 2 b) 5 c) 3 d) 4

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 126 views

An electron having an energy of 20 eV enters a magnetic field of 0.02 webers/sqm at an angle of 30degrees to the field. The time of travel (in nS)of the electron for one revolution is about  A) 1.78 B) 4.21 C) 7.82 D) 10.24 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 8 views

State the functions of fuel system and exhaust system of a diesel power station.

asked Sep 8, 2018 by Shimroz123
1 answer 16 views

The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are (A) 0.5 pu, 0.866 pu (B) 0.866 pu, 0.5 pu (C) 0.707 pu, 0.707 pu (D) 0.5 pu, 0.5 pu

asked Apr 28, 2018 in Electrical Machine by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...