# State any two disadvantages of one wattmeter method of measurement of 3 phase power.

73 views
State any two disadvantages of one wattmeter method of measurement of 3 phase power.

State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for unbalanced load 3. It is used for star connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

## Related questions

In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was?

In a 3-phase power measurement by two wattmeter method the reading of one of the wattmeter was zero. The power factor of the load must be?

The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is (A) zero (B) 0.5 (C) between zero and 0.5 (D) between 0.5 and unity

List any two methods of reactive power measurement in 3 phase circuit.

Merits of two wattmeter method

State any four advantages and four disadvantages of diesel electric power plant.

Write any two disadvantages of hydro power plant.

Explain V- I method of measurement of medium resistance.

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the connections of current coil. the power factor and reactive power of the load is A) 0.2 & 6 kVAR B) 0.2 & 6 √3 kVAR C) 0.32 & 2 kVAR D) 0.32 & 2 √3 kVAR

Measurement of power and power factor of a 3-phase system by two wattmeter method can be obtained in case of  1. Balanced load and balanced source  2. Balanced source with 3-phase 3-wire unbalanced load  3. Unbalanced source with 3-phase 3-wire balanced load  4. Balanced source with 3-phase 4-wire unbalanced load  5. unbalanced and unbalanced source    (a) 1 only (b) 2, 3 and 5 (c) 1, 2, 3, 4 and 5 (d) 1, 2, 3 and 5

Draw and explain bulk correction method for power factor & control.

Write any two disadvantages of ammeter shunts.

In two -wattmeter method of power measurement, if one wattmeter shows negative reading, then the power factor of the circuit is treated as (A) Unity (B) Lagging (C) Leading (D) Zero

State any four errors that occur in dynamometer type wattmeter

For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging:

In the measurement of three phase power by two wattmeter method, if the two wattmeter readings are equal then power factor of the circuit is  (A) 0.8 lag (B) Unity (C) 0.8 lead (D) Zero

Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil connected in the A and C lines. The phase sequence is ABC. If the wattmeter with its current coil in A -phase line reads zero, then the power factor of the 3 -phase load will be

With a neat sketch explain working of 1 phase dynamometer type power factor meter.

The product of apparent power and cosine of the phase angle between circuit voltage and current is?

State two advantages and two disadvantages of photoelectric pick-up speed measurement method.

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

In an alternator at lagging power factor the generated voltage per phase as compared to that at unity power factor?

Explain power relations in three phase circuit.

Explain power in single phase AC circuit.

State the effects of errors in dynamometer type wattmeter due to i) pc- inductance ii) pc- capacitance iii) mutual inductance iv) Connection.

State various types of errors in wattmeter.

What are some disadvantages of hydroelectric power plant?

State the significance of term measurement.

In the measurement of power by two wattmeter method, when the readings of the two wattmeters are equal, the power factor is (A) Zero (B) Leading (C) Lagging (D) Unity

List any four errors in induction type energy meter. Give method of compensation for each.