17 views
by
Draw a neat sketch of 1-ph induction type energy meter and write operating principle of it. 

1 Answer

0 votes
by

Operating Principal:- The disc is placed between the two-flux due to pressure coil and flux due to current coil, which will set up torque on the disc which is proportional to power causing the disc to rotate. As shown in the diagram electromagnets, eddy currents will be induced on the disc by two fluxes 

OR 

An aluminum disc is placed inside a magnetic core with two limbs. One carries a voltage coil so its flux is proportional to voltage, the second carries a current coil so its flux is proportional to current.

Related questions

1 answer 10 views

State the function and shape of following parts used in induction type energy meter: i) Series magnet ii) Shunt magnet iii) Al disc iv) Brake magnet

asked Sep 6, 2018 by Shimroz123
1 answer 15 views

List any four errors in induction type energy meter. Give method of compensation for each.

asked Sep 5, 2018 by Shimroz123
1 answer 37 views

An induction type energy meter is found to run fast. Correction for this error can be made by  (A) Over-load compensation. (B) Voltage compensation. (C) Moving the brake magnet away from the centre of the disc. (D) Moving the brake magnet towards the centre of the disc.

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 15 views

With a neat sketch explain working of 1 phase dynamometer type power factor meter.

asked Sep 6, 2018 by Shimroz123
1 answer 11 views

Why energy meter is integrating type measuring instrument?

asked Sep 5, 2018 by Shimroz123
1 answer 13 views

Draw a block diagram of electronic energy meter. Write function of each block.

asked Sep 6, 2018 by Shimroz123
1 answer 29 views

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
1 answer 110 views

Draw the diagram and explain the working of ferrodynamic type frequency meter. 

asked Sep 6, 2018 by Shimroz123
1 answer 10 views

Draw and describe working of electronic energy meter.

asked Sep 6, 2018 by Shimroz123
1 answer 6 views

Describe principle of operation of Doppler type ultrasonic flow meter with diagram. 

asked Sep 8, 2018 by Shimroz123
1 answer 30 views

With neat diagram explain calibration of energy meter by direct loading method.

asked Sep 6, 2018 by Shimroz123
1 answer 9 views

Write any two advantages of digital energy meter.

asked Sep 5, 2018 by Shimroz123
2 answers 3 views

State the meaning of creeping error in 1 phase energy meter.

asked Sep 6, 2018 by Shimroz123
1 answer 29 views

Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses. 

asked Sep 22, 2018 in Energy Conservation And Audit by Shimroz123
1 answer 19 views

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
2 answers 66 views

Explain working of Weston type frequency meter.

asked Sep 5, 2018 by Shimroz123
1 answer 53 views
3 answers 88 views

What type of meter is used to measure current?

asked Mar 10, 2018 in Electrical Measurements and Instrumentation by Quiz
1 answer 22 views

Phantom loading for testing of energy meter is used (A) to isolate the current and potential circuits (B) to increase power loss during testing (C) for meters having low current ratings (D) to test meters having a large current rating for which loads may not be available

asked Apr 28, 2018 in Electronics Engineering by Shimroz123
1 answer 22 views

In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

asked Apr 28, 2018 in Switchgear And Protection by Shimroz123
1 answer 8 views

What is meant by energy meter constant?

asked Sep 6, 2018 by Shimroz123
1 answer 13 views

Draw a neat sketch of moving primary fixed secondary double sided LIM. Write one advantage and one disadvantage of it. 

asked Sep 2, 2018 by Shimroz123
2 answers 35 views

Explain energy conservation technique “by improving power quality” for induction motor.

asked Sep 22, 2018 in Energy Conservation And Audit by Shimroz123
1 answer 19 views

With neat sketch explain working of Weston type synchroscope.

asked Sep 6, 2018 by Shimroz123
1 answer 4 views

Write the working of L-C-R meter with suitable sketch.

asked Sep 6, 2018 by Shimroz123
1 answer 39 views

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

asked May 3, 2018 in Electrical machine design by Shimroz123
1 answer 402 views

Draw the block diagram of basic wind energy conversion system and write function of each block. 

asked Sep 8, 2018 by Shimroz123
1 answer 5 views

Draw construction of Megger and write operating principle of it.

asked Sep 6, 2018 by Shimroz123
1 answer 7 views

Define energy. Write unit of it.

asked Sep 6, 2018 by Shimroz123
1 answer 24 views

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 589 views

Draw a neat labelled diagram of feeding post and write any four points related to it.

asked Sep 2, 2018 by Shimroz123
1 answer 36 views

A piezo-electric type pressure sensor has a sensitivity of 1 mV/kPa and a bandwidth of 300 Hz to 300 kHz. For a constant (dc) pressure of 100 kPa, the steady state output of the sensor in millivolt is (A) 0 (B) 2 (C) 4 (D) 6

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 18 views

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

The operation of a ramp type Digital Voltmeter is based on the principle of (A) Voltage-to-current conversion. (B) Voltage-to-time conversion. (C) Current-to-time conversion. (D) Current-to-frequency conversion.

asked Apr 28, 2018 in Digital Instrumentation by Shimroz123
1 answer 6 views

With neat diagram explain constructional details of dynamometer type wattmeter.

asked Sep 6, 2018 by Shimroz123
2 answers 160 views

Explain construction & working of attraction type M.I. instrument with neat diagram.

asked Sep 5, 2018 by Shimroz123
1 answer 17 views

Draw and explain the working principle of turbine type flow meter. Mention its Application area.

asked Sep 13, 2018 by Shimroz123
1 answer 78 views

State starters used for i) 3-Ph squirrel cage induction motor (3HP) ii) D.C. motor 

asked Sep 18, 2018 in Industry Electrical Systems-I by Shimroz123
1 answer 9 views

Write any two advantages of MI type instrument.

asked Sep 5, 2018 by Shimroz123
1 answer 11 views

Draw a neat sketch of earth fault protection of auxiliary circuit of electric loco. State the function of relay and isolating resistance.

asked Sep 2, 2018 by Shimroz123
1 answer 20 views

In a single-phase induction motor, the operating direction is determined by the ________ A) Rotor B) Stator C) Starting circuit D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...