2 views
by
State the use of shunt and series resistance used in extension of meter.

1 Answer

0 votes
by

Use of shunt and series resistance: i) Use of shunt: To extend the range of Ammeter. ii) Use of series resistance: To extend the range of Voltmeter.

Related questions

1 answer 10 views

State the function and shape of following parts used in induction type energy meter: i) Series magnet ii) Shunt magnet iii) Al disc iv) Brake magnet

asked Sep 6, 2018 by Shimroz123
1 answer 36 views

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

asked May 3, 2018 in Electrical Machine by Shimroz123
1 answer 6 views

State the advantages of instrument transformer in using for extension of range of meters. 

asked Sep 6, 2018 by Shimroz123
1 answer 18 views

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 22 views

What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 134 views

Shunt compensation in an EHV line is used to (A) Improve stability. (B) Improve the voltage profile. (C) Reduce the fault level. (D) Substitute for synchronous phase modifier.

asked May 8, 2018 in Power system by Shimroz123
1 answer 22 views

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

asked May 8, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

Why shunt capacitor is used?

asked Mar 15, 2018 in Electronics Engineering by Quiz
1 answer 22 views

Phantom loading for testing of energy meter is used (A) to isolate the current and potential circuits (B) to increase power loss during testing (C) for meters having low current ratings (D) to test meters having a large current rating for which loads may not be available

asked Apr 28, 2018 in Electronics Engineering by Shimroz123
3 answers 88 views

What type of meter is used to measure current?

asked Mar 10, 2018 in Electrical Measurements and Instrumentation by Quiz
1 answer 27 views

Series capacitive compensation in EHV transmission line is used to

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 13 views

Series reactors are used to

asked Apr 26, 2018 in Switchgear And Protection by Shimroz123
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

asked Mar 21, 2018 in DC generator by Shimroz123
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
2 answers 3 views

State the meaning of creeping error in 1 phase energy meter.

asked Sep 6, 2018 by Shimroz123
1 answer 18 views

State the principle of solar cell. What is necessity of series and parallel connection of solar cells.

asked Sep 7, 2018 by Zeeshan
1 answer 9 views

State necessity of series connection and parallel connection of batteries.

asked Sep 4, 2018 by Shimroz123
1 answer 24 views

State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

asked Sep 5, 2018 by Shimroz123
1 answer 19 views

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 391 views

In which of the following transmission lines, the value of the Shunt admittance should be approximated to zero ? (A) A 66 kV 35 km long line (B) A 132 kV 200 km long line (C) A 220 kV 300 km long line (D) A 400 kV 500 km long line

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 9 views

State the range for low and medium resistance.

asked Sep 6, 2018 by Shimroz123
1 answer 29 views

Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses. 

asked Sep 22, 2018 in Energy Conservation And Audit by Shimroz123
1 answer 110 views

Draw the diagram and explain the working of ferrodynamic type frequency meter. 

asked Sep 6, 2018 by Shimroz123
1 answer 53 views
1 answer 61 views

In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

asked May 1, 2018 in Network Analysis by Shimroz123
1 answer 22 views

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 25 views

The series and parallel resonance on L-C circuit differs in that?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 20 views

kWh meter is the electric meter that measures the amount of electrical _________ in kWh that was consumed in the house.  (A) Energy (B) Current (C) Voltage (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
1 answer 10 views

Give the classification of the errors used in measuring instrument & state the reason for their occurrence.

asked Sep 6, 2018 by Shimroz123
1 answer 17 views

Draw a neat sketch of 1-ph induction type energy meter and write operating principle of it. 

asked Sep 6, 2018 by Shimroz123
1 answer 10 views

Draw and describe working of electronic energy meter.

asked Sep 6, 2018 by Shimroz123
1 answer 26 views

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...