# How many insulator disc used for 33 kV transmission voltage line?

55 views
How many insulator disc used for 33 kV transmission voltage line?

5,As 33kv is Vrms

## Related questions

The number of insulator discs (each rated 11 kV) required in a suspension type insulator string of 220 kV line is

A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line

How does the resistance of a conductor compare to that of an insulator?

If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19

The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

Stability of a transmission line can be increased by

State functions of ; i) Cable box ii) Guard wire iii) Shackle insulator iv) Stay wire used in service connection

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

What is another name for an insulator?

What type of insulator will be used if the direction of the transmission line is to be changed?

In case of a ‘High Voltage DC’ transmission, how many minimum conductors are required?

Series capacitive compensation in EHV transmission line is used to

The voltages across various discs of suspension insulators having identical discs are different due to:  (A) Surface leakage currents  (B) Series capacitance of lines  (C) Shunt capacitance to ground  (D) Series and shunt capacitances

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

Why high voltage is used in power transmission?

A suspension type insulator has 2 units with self capacitance C and ground capacitance of 0.2 C. Each unit can withstand for a maximum voltage of 11 kV. Its string efficiency is  (A) 78% (B) 82% (C) 80% (D) 84%

What is the difference between an insulator and a dielectric?

what is insulator ?

In which of the following transmission lines, the value of the Shunt admittance should be approximated to zero ? (A) A 66 kV 35 km long line (B) A 132 kV 200 km long line (C) A 220 kV 300 km long line (D) A 400 kV 500 km long line

In case the height of transmission tower is increased, which of the following parameter is likely to change?  (A) Resistance (B) Inductance (C) Capacitance (D) None of the above

The purpose of guard ring in transmission lines is to  (1) reduce the earth capacitance of the lowest unit. (2) increase the earth capacitance of the lowest unit. (3) reduce the transmission lines losses. (4) reduce the reactance of the line

A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9

The sag of a transmission line is least affected by (A) Self weight of the conductor. (B) Temperature of the surrounding air. (C) Current through the conductor. (D) Ice deposited on the conductor.

A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km

Transmission efficiency of a transmission line increases with the

What are the losses in a transmission line?

what is mean by medium transmission line ?

what is mean by short transmission line ?

what is mean by long transmission line ?

A 100 km transmission line is designed for a nominal voltage of 132 kV and consists of one conductor per phase. The line reactance is 0.726 ohm/km. The static transmission capacity of the line, in MW, would be   (a) 240 (b) 132 (c) 416 (d) 720

The main consideration for operating transmission line at high voltage is (a) to increase efficiency only. (b) to reduce power loss only. (c) to increase power transmission capability only. (d) All of the above

Which of the following is used for power factor improvement in transmission line ? (a) Three phase induction (b) An overexcited three phase synchronous motor running on no load (c) Three phase AC series motor (d) Choke

The voltage of transmission can be regulated by  (A) Use of tap changing transformers (B) Switching in shunt capacitors at the receiving end during heavy loads (C) Use of capacitors to neutralize the effect of series reactance (D) Any of the above methods

The permissible voltage variation in transmission and distribution system is:  (A) ± 0.1% (B) ± 1% (C) ±10% (D) ± 25%

In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

Why is voltage increases before transmission?

What is meant by extra high voltage transmission?

What are the advantages of high voltage transmission?

The power flow problem mathematical model for a linear transmission network (A) is non-linear (B) is linear (C) considers time variation of generation (D) does not consider tap-changing transformers

The standard for long distance analog signal transmission in process control industry is (A) 4-20 mV (B) 0-20 mA (C) 4-20 mA (D) 0-5 V

For extra high voltage ac transmission lines, conductors used are (a) All aluminium (b) All steel (c) AAAC (d) ACSR