47 views
in Electrical Engineering by
if the resistance is connected in parallel the total resistance decreases why?

1 Answer

0 votes
by
Because if the resistances are connected in parallel it provide a conducting path for current to flow. So more the current paths less the resistance

Related questions

1 answer 22 views

What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

When an additional resistor is connected across an existing parallel circuit, the total resistance: A. remains the same B. decreases by the value of the added resistor C. increases by the value of the added resistor D. decreases

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

What is the equivalent resistance of a network having 5 resistors of each 10ohm connected in parallel?  (A) 10 Ohms (B) 50 Ohms (C) 500 Ohms (D) 2 Ohms 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

When ‘n’ resistances each of value ‘r’ are connected in parallel, then the resultant resistance is ‘x’. When these ‘n’ resistances are connected in series, total resistance is  (A) n2X (B) X/n (C) n2/X (D) nX2

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
2 answers 201 views

why the electrical appliances are connected in parallel ?

asked Aug 14, 2017 in Electrical Engineering by Zeeshan
1 answer 25 views

A sine wave voltage is applied across an inductor. When the frequency of the voltage is decreased, the current decreases.

asked Nov 23, 2017 in Electrical Engineering by James
2 answers 26 views

How will the total capacitance change, when two capacitors are connected in parallel?

asked May 29, 2018 in Capacitor by Shimroz123
1 answer 10 views

When two 100 kΩ resistors are connected in parallel, net resistance is

asked May 15, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

A parallel combination of capacitance C and resistance R is connected in series with inductance L and small resistance r. Under what condition will the circuit be non-reactive?  (A) C=LR (B) C=LR2 (C) C=L/R2 (D) C=L/R

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
2 answers 26 views

Three lamps are connected in parallel across a 120 Volt source. If one lamp burns out, the remaining two will be: A. Glow dimmer B. Glow brighter C. Not light D. Glow with the same brightness as before

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
3 answers 52 views

what will be the capacitance if three capacitors connected in parallel each having value of 0.5 micro Farad ?

asked Dec 11, 2017 in Electrical Engineering by Quiz
0 answers 126 views
0 answers 22 views

If two 3-phase transformers with unequal voltage ratios are connected in parallel, the result is (A) circulating current on no-load (B) no circulating current on no-load (C) dead short-circuit (D) equal no-load secondary emfs 

asked Jun 4, 2018 in Electrical Machine by Shimroz123
1 answer 14 views

Two resistance 100Ω ± 5Ω ± 15Ω are connected in series. If the errors are specified as standard deviations, the resultant error will be

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

Consider the following statements : If a high Q parallel resonant circuit is loaded with a resistance  1. The circuit impedance reduces.  2. The resonant frequency remains the same.  3. The bandwidth reduces.  Which of the above statements is/are correct ?

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

If supply voltage decreases by 4% the torque in 3-phase induction motor would decrease by (1) 4% (2) 16% (3) 8% (4) 7.84%  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
2 answers 76 views

 With three resistances connected in parallel, if each dissipates 20 W the total power supplied by the voltage source equals?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 8 views

Resistance of a material always decreases if?

asked Mar 25, 2018 in Basic concepts by Shimroz123
0 answers 45 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 48 views

Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

A network consists of several inductances connected in parallel. The equivalent inductance of the network is given by (A) the sum of the individual inductances. (B) the reciprocal of the sum of the individual inductances. (C) the sum of the reciprocals of individual inductances. (D) the reciprocal of the sum of reciprocals of individual inductances.

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

 The number of parallel paths in the armature winding of a 4 -pole, wave connected d.c. machine having 28 coilside is : -  a) 28 b) 14 c) 4 d) 2

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

If the lagging power factor of the load decreases, the line losses will (A) Decrease (B) Increase (C) Flrst decrease and then Increase (D) Remain same

asked May 12, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

asked May 17, 2018 in Electronics communication by Shimroz123
0 answers 17 views

A binary ladder with R -2R network has R = 20K Ohms. The total resistance looking out toward the LSB input is (a) 20KOhms (b) 40KOhms (c) 10KOhms (d) 30KOhms

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 121 views

Two heater wires of equal length are connected first in series and then in parallel. The ratio of heat generated from series to parallel connection will be (a) 4 : 1 (b) 2 : 1 (c) 1 : 2 (d) 1 : 4

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Two transformers having the same p.u. impedance connected in parallel share the connected load (A) equally (B) in proportion to the respective ratings (C) in proportion to the voltage ratio (D) in proportion to the zero phase displacement

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

The number of parallel paths in armature winding of four pole wave winding connected dc machine having 22 coil sides is (1) 4 (2) 22 (3) 2 (4) 11 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
3 answers 134 views

Three resistors of 4 Ω, 6 Ω and 9 Ω are connected in parallel. Which resistor consumes the maximum power?  (A) 4 Ω (B) 6 Ω (C) 9 Ω (D) 17 Ω

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

Resistance of a copper wire decreases when ......................increases

asked May 14, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

Which of the following will happen if a voltmeter is connected like an ammeter in series to the load ? (A) There will be almost no current in the circuit. (B) The meter will burn. (C) The measurement will be trio high. (D)  A very high current will flow.

asked May 12, 2018 in Electrical Engineering by Shimroz123
0 answers 41 views

If an energy meter disc makes 10 revolutions in 100 seconds when a load of 450W is connected to it, the meter constant in revolutions per kWh is  A) 1000 B) 500 C) 1600 D) 800

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 67 views

If one of the control springs of PMMC ammeter is broken when it is connected in a circuit, the meter will read  A) Half the correct value of current B) Twice the correct value of current C) An indefinite figure D) Zero

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 1,386 views

In an amplitude modulated system if the total power is 600W and the power in the carrier is 400W, the modulation index is  a. -0.5 b. 0.75 c. 0.9 d. l

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 49 views

An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

If a cell connection is reversed in parallel group, what will happen? A. Open circuit B. All cells will be equally charged C. short circuit D. Nothing will happen 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

Three 60 W bulbs are in parallel across the 230 V power line. If one bulb burns out

asked May 14, 2018 in Electrical Engineering by Shimroz123
1 answer 80 views

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

When one leg of parallel circuit is opened out the total current will?

asked Mar 25, 2018 in Basic concepts by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...