# what is a pony motor ?

39 views
what is a pony motor ?

by
pony motor is a small induction motor

## Related questions

0 answers 31 views
1 answer 18 views

A pony motor is basically a?

0 answers 11 views

What is the RPM of a DC motor?

1 answer 178 views
1 answer 30 views

What is the definition of induction motor?

1 answer 71 views

What is the function of induction motor?

0 answers 17 views

What is the principle of synchronous motor?

0 answers 23 views

What is the use of synchronous motor?

0 answers 17 views

What is the principle of AC motor?

1 answer 58 views

What is mean by plugging in three phase induction motor?

1 answer 20 views

what is separately excited motor ?

1 answer 29 views

AC motor

2 answers 109 views

what is the difference between synchronous and asynchronous motor?

1 answer 31 views
1 answer 47 views

What will happen if you increase the current in the motor?

0 answers 9 views

What are the parts of AC motor?

2 answers 91 views

What are the speed control methods of dc motor?

1 answer 30 views

what are the types of dc motor?

0 answers 26 views

A 200 V dc motor takes a field current of 2 A to generate a back emf of 180 V. If the field winding resistance is 80 Ω, the resistance of the shunt field regulator is (A) 10 Ω (B) 20 Ω (C) 100 Ω (D) 180 Ω

1 answer 27 views

For a 1.8o, 2-phase bipolar stepper motor, the stepping rate is 100 steps/second. The rotational speed of the motor in rpm is  (A) 15 (B) 30 (C) 60 (D) 90

1 answer 22 views

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

1 answer 33 views

A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be (A) 23.06 kW (B) 24.11 kW (C) 25.01 kW (D) 26.21 kW

1 answer 22 views

In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high resistance winding. (C) Small current flows through the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

1 answer 36 views

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

1 answer 38 views

The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

1 answer 19 views

Slip test is performed to determine :  (A) Slip in an induction motor  (B) Xd and Xq in a salient pole alternator  (C) Synchronous impedance in an alternator  (D) Positive and negative sequence impedances of an alternator

1 answer 21 views

Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

1 answer 32 views

A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for

1 answer 28 views

The function of a brush and commutator arrangement in a dc motor is to  (1) produce unidirectional torque (2) produce unidirectional current in the armature (3) help in changing the direction of rotation of the armature (4) reduce sparking

1 answer 23 views

In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then (A) the flux is constant (B) the flux first decreases and then increases in the same direction (C) the flux increases and decreases in the opposite direction with the same magnitude (D) current flows through the rotor

1 answer 152 views

The effect of increasing load on a synchronous motor running with normal excitation is (A) Increase both its Ia and power factor. (B) Decrease Ia, but increase power factor. (C) Increase Ia, but decrease power factor (D) Decrease both Ia and power factor.

1 answer 29 views

An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is (A) 5.06 kW (B) 0.3 kW (C) 100 kW (D) 83.33 kW

1 answer 21 views

In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is (A) 0.2 Ω (B) 0.3 Ω (C) 0.4 Ω (D) 0.5 Ω

1 answer 30 views

A three-phase synchronous motor connected to ac mains is running at full load and unity power factor. lf its shaft load is reduced by half and field current is held constant then its new power factor will be

0 answers 39 views

The rotor winding of a three phase wound rotor induction motor is equipped with a three phase diode rectifier connected to the slip rings and rectifier output is connected with chopper drive. Compared to conventional rotor resistance control scheme, the chopper controlled method  A) Enhances the motor rating B) Maintains the motor rating as such C) Derates the motor D) None of the above

1 answer 21 views
1 answer 13 views
1 answer 15 views
1 answer 18 views

As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit?

1 answer 17 views
1 answer 29 views
1 answer 13 views
1 answer 28 views
1 answer 21 views
1 answer 18 views
1 answer 12 views
1 answer 14 views
1 answer 30 views
1 answer 13 views
1 answer 14 views