107 views
in Electrical Engineering by

3 Answers

0 votes
by
No, we need neutral wire to get voltage difference.
0 votes
by
The bulb will light due to phase voltage (415v)
0 votes
by
Due to no potential difference between the ends of the circiut there is no existance of current 
by
There is a 415 line voltage.

Related questions

1 answer 25 views

In a three-phase supply floating neutral is undesirable because it way give rise to?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The magnetic neutral plane shifts in a dc machine (A) in the direction of motion of motor (B) in the direction of motion of generator (C) due to increase in the field flux (D) cause reduction of flash over between commutator segments

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
2 answers 52 views

If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

asked Oct 21, 2017 in Electrical Engineering by Quiz
1 answer 14 views

Two incandescent light bulbs of 40 Wand 60 W rating are connected in series across the mains, then .  A) The bulbs together consume 100 W B) The bulbs together consume 50 W C) The 60 W bulb glows brighter D) The 40 W bulb glows brighter

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 22 views

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 50 views

Explain the meaning of following terms: i) MCB ii) Socket outlet iii) Neutral iv) Fuse-link

asked Sep 20, 2018 in Industry Electrical Systems-I by Shimroz123
1 answer 84 views

To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

asked Apr 27, 2018 in Switchgear And Protection by Shimroz123
3 answers 113 views

Which color wire is neutral?

asked Dec 22, 2017 in Fundamentals of electrical power systems by Quiz
1 answer 12 views

Name two good conductors, two good insulators, and two semiconductors.

asked Jun 29 by Shimroz123
1 answer 12 views

Three 60 W bulbs are in parallel across the 230 V power line. If one bulb burns out

asked May 14, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 28 views

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 79 views

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

List two types of oscillator, which generates frequency in RF range.

asked Sep 5, 2018 by Shimroz123
1 answer 19 views

Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 22 views

The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :  (A) 34.64 kVA (B) 75 kVA (C) 20 kVA (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

Which of the following connection of transformers will give highest value of secondary voltage ? (A) Delta primary delta secondary (B) Delta primary star secondary (C) Star primary star secondary (D) Star primary delta secondary

asked May 8, 2018 in Electrical Engineering by Shimroz123
0 answers 146 views

 A series generator is supplying power to DC bus bar. If the prime mover fails, then the machine will operate as (A) DC series motor rotating in the same direction (B) DC series motor rotating in the opposite direction (C) DC series generator rotating in the same direction (D) Machine will stop

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

One 200 V, 100 W bulb is connected in series with primary of a 200 V, 10 kVA transformer. If its secondary is kept open circuited, then the bulb would have (1) Full brightness (2) Poor brightness (3) A little less than full brightness (4) More than full brightness 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 22 views

List at least two examples that show how static electricity can be generated.

asked Jun 29 by Shimroz123
1 answer 9 views

Merits of two wattmeter method

asked Sep 6, 2018 by Shimroz123
1 answer 47 views

Explain two-quadrant chopper.........

asked Feb 15, 2018 in Unit 2 by Quiz
0 answers 121 views

Two heater wires of equal length are connected first in series and then in parallel. The ratio of heat generated from series to parallel connection will be (a) 4 : 1 (b) 2 : 1 (c) 1 : 2 (d) 1 : 4

asked May 25, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

If the supply frequency of a 3-phase induction motor is ‘f’, then frequency of rotor emf at motor slip ‘s’ will be   (a) sf (b) (1 – s)f (c) f/s (d) None of these 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 70 views

The power in a 3-phase load is measured by two watt meters. If one watt meter reads zero, then the load power factor is (A) Zero (B) 0.5 (C ) 0.866 (D) unity 

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 440 views

A 220 V, 200 W bulb and a 220 V, 100 W bulb are connected in series across a 220 V supply, the power consumed by them will be (a) 33.3 W (b) 66.6 W (c) 100 W (d) 300 W

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 19 views

Two transformers A and B having equal outputs and voltage ratios but unequal percentage impedances of 4 and 2 are operating in parallel. The transformer A will be overloaded by 

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 68 views

 An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is (A) + 120 V (B) – 120 V (C) – 60 V (D) + 60 V

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 34 views

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 30 views

A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 50 views

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 70 views

A voltage source inverter will have better performance if its  (1) load inductance is small and source inductance is large.  (2) both load and source inductance are small.  (3) both load and source inductances are large.  (4) load inductance is large and source inductance is small. 

asked Apr 30, 2018 in Power Electronics by Shimroz123
1 answer 65 views

A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

asked Apr 29, 2018 in Power Electronics by Shimroz123
0 answers 10 views

In CRO, Lissajous pattern will be a straight line, if the two signals are of same frequency with a phase difference of (a) 0° (b) 180° (c) 360° (d) All of these 

asked May 25, 2018 in Oscilloscope by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...