# What is the percentage of stray losses in DC machine?

32 views
What is the percentage of stray losses in DC machine?

by

Percentage of stray losses in DC machine is about 1 % .

## Related questions

The induced emf in the armature of a lap -wound four -pole dc machine having 100 armature conductors rotating at 600 rpm and with 1 Wb flux per pole is  (1) 1000V (2) 100V (3) 600V (4) 10,000V

In DC motor iron losses are occurred in?

Aluminium is not used as winding wire for the armature of a dc machine because  (1) aluminium has low resistivity (2) a large winding space is taken by aluminium conductors and creates jointing problems (3) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

The magnetic neutral plane shifts in a dc machine (A) in the direction of motion of motor (B) in the direction of motion of generator (C) due to increase in the field flux (D) cause reduction of flash over between commutator segments

A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is

In a dc machine, interpoles are used to  (1) neutralize the effect of armature reaction in the interpolar region (2) generate more induced emf in the armature (3) avoid interference of the armature flux with the main -field flux (4) reduce the demagnetizing effect of armature reaction

Brushes of DC machine are made up of ?

A 36 slot, 4 -pole, dc machine has a simplex lap winding with two conductors per slot. The back pitch and front pitch adopted could be respectively

What arc the errors occurring in measuring devices due to stray magnetic field and temp '? Explain how to compensate them.

The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is A) 50 W B) 66 W C) 68 W D) 70 W

What are the types of power losses in inductor?

What is the percentage error when 3 resistors with ratings 100 Ω at 5%, 150 Ω at 6% and 250 Ω at 8% respectively, are connected in series? A) 6.33% B) 6.80% C) 19% D) None of these

True value has been 50 whereas measured value is 40 then the percentage error in the reading will be ______.  (A) 20% (B) 40% (C) 50% (D) 30%

What are the losses in a transmission line?

Two transformers A and B having equal outputs and voltage ratios but unequal percentage impedances of 4 and 2 are operating in parallel. The transformer A will be overloaded by

What is fuzzy logic in a washing machine?

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

The friction losses in Real Transformers are :  (A) 0% (B) 5% (C) 25% (D) 50%

In synchronous motor, does the winding losses vary with load?

Explain the on state losses in power BJT.

Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses.

Which of the following can reduce the Eddy current losses? A) By making the core of a stack of plates electrically insulated from each other B) By making the core of solid block C) By increasing the applied voltage  D) None of these

Explain the electrical losses of magnetic materials used for the cores of inductors and transformer.

Analyze the differences of FOC and DTC. The switching frequency of FOC is 1.3 kHz and the average switching frequency of DTC is the same.

In a synchronous machine, if the field flux axis ahead of the armature field axis in the direction of rotation, the machine is operating as  (1) synchronous motor (2) synchronous generator (3) asynchronous motor (4) asynchronous generator

Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

Reduction in core losses and increase in permeability are obtained with transformer employing?

Losses which occur in rotating electric machines and do not occur in transformers are?

In a synchronous motor which losses varies with load?

Which machine is the exciter of synchronous machine?

Auto-transformer makes effective saving on copper and copper losses, when its transformation ratio is?

The 'Equal area criterion' for the determination of transient stability of a synchronous machine connected to an infinite bus  (1) ignores line as well as synchronous machine resistance and shunt capacitances.  (2) assumes accelerating power acting on the rotor as constant.  (3) ignores the effect of voltage ... inherent damping present in the machine.  (4) takes into consideration the possibility of machine losing synchronism after it has survived during the first swing.