# Explain the single pass transformer design procedure step by step by giving its flowchart.

23 views
in Unit 3
Explain the single pass transformer design procedure step by step by giving its flowchart.

by

single pass transformer design procedure step by step by giving its flowchart:

## Related questions

Explain the iterative inductor design procedure. Show the design procedure flowchart.

What are the design constraints of transformer design?

Describe different RT level computational and sequential components used to design single function processors.

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

Explain the procedure for disposal of nuclear power plant.

A second order system shows 100% overshoot in its unit step response. It can be categorized as (A) underdamped system. (B) overdamped system. (C) Critically damped system. (D) undamped system.

Explain the electrical characteristics of transformer.

What is design technology? Explain top down design process.

Explain design constraint of filter inductor design.

Describe procedure for calibration of ammeter with diagram.

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

A 1000Ohm, 1 Watt resistor can safely pass a current of

What kinds of materials can not electricity pass through?

write short notes on Low-pass filter.

What is the Laplace transform of step signal of 5 units magnitude?  A) 5s B) 5/s C) s/5 D) 1/s

What does double integration of a unit step function lead to? A) A doublet B) A ramp C) An impulse D) A parabola

Integration of step signal gives (A) Impulse signal. (B) Ramp function. (C) Parabola. (D) Square pulse.

Draw the single stage RC coupled amplifier circuit and explain its’s operation.

explain the working of single phase induction motor.

Sketch internal design of 4x3 ROM.

What is VLSI logic design?

What is digital circuit design?

What is electronic circuit design?

What is an electronic design?

The maximum load that a power transformer can carry is limited by its?

A switch tail ring counter is made by using a single D-FF. The resulting circuit is (A) T-FF (B) D-FF (C) SR-FF (D) JK-FF

Explain single line diagram.

Explain power in single phase AC circuit.

Explain buck or step down converter and draw its waveforms.

State what is the significance of conducting phasing out test on a 3-phase transformer? Explain its procedure with a suitable connection diagram.

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

A Step Up transformer :  (A) Steps up the level of Voltage (B) Steps down the level of current (C) Step up the level of Frequency (D) (a) and (b) only

Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

In a single-phase transformer, the magnetizing current is (A) in phase with the no-load current (B) in quadrature with the no-load current (C) the product of no-load current and power factor (D) in phase with the flux in the core

In a transformer the resistance between its primary and secondary should be?

In a single crystal of an intrinsic semiconductor, the number of free carriers at the Fermi level at room temperature is: A) Half the total number of electrons in the crystal B) Zero C) Half the number of atoms in the crystal D) Half the number of free electrons in the crystal

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W