How can BJT be used as an amplifier?

21 views
How can BJT be used as an amplifier?

Related questions

What is a BJT amplifier?

The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

What type of biasing is used in CE amplifier?

If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55

How can a magnetic field be used to generate an electric current?

What is the difference between BJT and FET?

How does an operational amplifier work?

How does negative feedback reduces distortion in an amplifier?

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

The gain of an ideal amplifier must be

An FET is a better chopper than a BJT because it has (A) lower offset voltage (B) higher series ON resistance (C) lower input current (D) higher input impedance

A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28

Define gain and bandwidth of an amplifier.

An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

What do you mean by frequency response of an amplifier?

What is stability in an amplifier?

Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO

Which of the following gates can be used to realize all possible combinational logic functions?  (i) OR gate (ii) NOR gate (iii) Exclusive OR gate (iv) NAND gate (v) AND gate  (A) (iii), (iv) and (v)  (B) (i), (iii) and (iv)  (C) (ii) and (iv)  (D) (i) and (v)

Which of the following can be used to measure the capacitance of a capacitor? A) Rheostat B) Schering bridge C) Wheatstone bridge D) None of these

A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region (OFF state) or in the saturation region (ON state). In the ON state, for the BJT  (A) both the base-emitter and base-collector junctions are reverse biased (B) the base-emitter junction is reverse ... (C) the base-emitter junction is forward biased, and the base-collector junction is reverse biased (D) both the base-emitter and base-collector junctions are forward biased

List configurations of BJT.

State the need of biasing of BJT.

Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Compare BJT with FET

Compare between BJT and FET on the basis of (i) Biolar/Unipolar (ii) Tharmal Runaway (iii) Noise (iv) Applications

Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

Is the input impedance of MOSFET more than BJT and FET?

What is a BJT?

What is the difference between beta and forced beta for BJT?

Explain open emitter BJT drive circuit.

Explain the formation of parasitic BJT and parasitic diode in Power MOSFET. Can parasitic diode be used in same power electronics applications?

Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Compare BJT, MOSFET and IGBT .