14 views
in Transformer by
Part of the transformer which is most subject to damage from overheating is?

1 Answer

0 votes
by

Part of the transformer which is most subject to damage from overheating is winding insulation.

Related questions

1 answer 27 views

Which of the following is not a part of transformer installation?  (A) Conservator (B) Breather (C) Buchholz Relay (D) Exciter

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 17 views

The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?

asked Mar 19, 2018 in Transformer by Zeeshan
0 answers 14 views

Can power surge damage your computer?

asked Mar 10, 2018 in Power quality by Quiz
1 answer 20 views

The voltage transformation ratio of a transformer is equal to the ratio of?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 26 views

The dielectric strength of transformer oil is expected to be?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 9 views
1 answer 16 views

The hum in a transformer is mainly attributed to?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 18 views

If a transformer is switched on to a voltage more than the rated voltage?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 15 views

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 46 views

An open-circuit test on a transformer is conducted primarily to measure?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 21 views

A no-load test is performed on a transformer to determine?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 26 views

Sumpner's test is conducted on transformer to determine?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 23 views

The secondary of a current transformer is always short-circuited under operating conditions because it?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 14 views

The efficiency of a transformer, under heavy loads, is comparatively low because?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 25 views

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 31 views

When secondary of a current transformer is open-circuited its iron core will be?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 13 views

The size of a transformer core will depend on?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 19 views

The path of magnetic flux in a transformer should have?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 10 views

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...