Can you help by answering this question?

The role of surge tank in a hydroelectric plant is to

14 views
in Transformer by
The efficiency of a transformer, under heavy loads, is comparatively low because?

1 Answer

0 votes
by
The efficiency of a transformer, under heavy loads, is comparatively low because copper loss becomes high in proportion to the output.

Related questions

1 answer 30 views

For a transformer, operating at constant load current, maximum efficiency will occur at?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 32 views

A transformer operates 24 hours day at full -load. It's full -load efficiency is :  (A) equal all day efficiency (B) more than all -day efficiency (C) less than all -day efficiency (D) equal to maximum efficiency

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

The secondary of a current transformer is always short-circuited under operating conditions because it?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 35 views

Transformer efficiency

asked Jun 11 by Shimroz123
1 answer 36 views

Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

The efficiency of two identical transformers under load conditions can be determined by?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 21 views

A heavy ladder resting on floor and against a vertical wall may not be in equilibrium, if?

asked Mar 22, 2018 in Engineering Mechanics by Shimroz123
0 answers 960 views

What is the difference between linear and nonlinear electrical loads?

asked Mar 10, 2018 in Power quality by Quiz
1 answer 14 views

If non-linear loads are connected to the power system, then (A) displacement power factor is same as the total power factor (B) displacement power factor is not equal to the total power factor (C) displacement power factor is due to harmonic currents (D) total power factor is due to fundamental component of current

asked Apr 28, 2018 in Power system by Shimroz123
0 answers 22 views

Why do non linear loads cause harmonics?

asked Mar 10, 2018 in Power quality by Quiz
1 answer 24 views

Transmission efficiency of a transmission line increases with the

asked Apr 26, 2018 in Switchgear And Protection by Shimroz123
1 answer 31 views

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 63 views

What is the difference between a line voltage and low voltage control system?

asked Mar 10, 2018 in High voltage engineering by Quiz
1 answer 18 views

What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 48 views

The overall efficiency of Thermal Power Plant is equal to _______________ .  (A) Regenerative Cycle Efficiency (B) Renkine Cycle Efficiency (C) Carnot cycle efficiency (D) None of the above

asked May 8, 2018 in Electric Power Generation by Shimroz123
1 answer 13 views

The rankine cycle efficiency of steam power plant is  (1) 60-80% (3) 30-45% (2) 45-80% (4) 20-30%

asked Apr 29, 2018 in Electric Power Generation by Shimroz123
1 answer 19 views

Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

asked May 8, 2018 in Electrical Engineering by Zeeshan
1 answer 78 views

What is the definition of extra low voltage?

asked Mar 10, 2018 in High voltage engineering by Quiz
1 answer 65 views

At which time power factor of the induction motor is low?

asked Mar 3, 2018 in Electrical Machine by Quiz
1 answer 20 views

The voltage transformation ratio of a transformer is equal to the ratio of?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 25 views

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 16 views

Unlike a shunt motor, it is difficult for a series motor to stall under heavy loading because?

asked Mar 26, 2018 in DC motor by Shimroz123
1 answer 49 views

In an AC. circuit, a low value of kVAR compared with kW indicates?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 39 views

Accurate measurement of very low resistances is possible with (A) Megger (B) Wheatstone Bridge (C) Kelvin’s Double Bridge (D) Wagner’s Earthing Device

asked Apr 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 29 views

For high efficiency of transfer of power, internal resistance of the source should be?

asked Mar 25, 2018 in Network Analysis by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...