Can you help by answering this question?

The cascade amplifier is a multistage configuration of

14 views
in Transformer by

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

High voltage winding of the transformer has less cross-sectional area.

Related questions

1 answer 42 views

The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross-sectional area of 100 cm2, and a maximum flux density of 1.0 T is (A) 100 (B) 200 (C) 222 (D) 400

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

A galvanised steel tower member has original length of 22cm and cross sectional area of 13 cm2. With working axial tensile load of 125 KN, the change in length was 0.2 mm. Calculate the percentage of elongation.  (A) 0.0712% (B) 0.00612% (C) 0.0909% (D) 0.19% 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
2 answers 31 views

What happens to the resistance of a wire when its length as well as the cross-sectional area are doubled? A) It doubles B) It becomes 4 times C) It becomes 2π times D) It remains the same

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

If the cross-sectional area of a magnetic field increases, but the flux remains the same, the flux density: A. increases B. decreases C. remains the same D. doubles

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

With the increase in the cross sectional area of the conductor, the value of resistance:  (1) Increase (2) Remain same (3) Decrease (4) None of these

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

Two copper conductors have equal length. The cross-sectional area of one conductor is four times that of the other. If the conductor having smaller cross-sectional area has a resistance of 40 ohms the resistance of other conductor will be?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 25 views

A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?

asked Mar 19, 2018 in Transformer by Zeeshan
1 answer 14 views

Part of the transformer which is most subject to damage from overheating is?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 10 views
1 answer 15 views

Two aluminium conductors have equal length. The cross-sectional area of one conductor is four times that of the other. If the conductor having smaller cross-sectional area has a resistance of 100 ohms the resistance of other conductor will be 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 13 views
1 answer 13 views

The size of a transformer core will depend on?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 23 views

The secondary of a current transformer is always short-circuited under operating conditions because it?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 16 views

The efficiency of a transformer, under heavy loads, is comparatively low because?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 20 views

The voltage transformation ratio of a transformer is equal to the ratio of?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 26 views

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 26 views

The dielectric strength of transformer oil is expected to be?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 20 views

The path of magnetic flux in a transformer should have?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 31 views

When secondary of a current transformer is open-circuited its iron core will be?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 26 views

During open circuit test of a transformer?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 13 views

A good voltage regulation of a transformer means?

asked Mar 19, 2018 in Transformer by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,503 questions

7,101 answers

134 comments

3,090 users

...