# The interaction between a transmission line and communication line is minimized by?

29 views

The interaction between a transmission line and communication line is minimized by transposing transmission as well as communication lines, increasing the height of the transmission line tower, increasing the distance between the two lines.

## Related questions

Transmission efficiency of a transmission line increases with the

The sag of a transmission line is least affected by (A) Self weight of the conductor. (B) Temperature of the surrounding air. (C) Current through the conductor. (D) Ice deposited on the conductor.

A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km

What is the difference between a line voltage and low voltage control system?

Stability of a transmission line can be increased by

The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

what is mean by medium transmission line ?

what is mean by short transmission line ?

what is mean by long transmission line ?

What is the difference between line and phase current?

What is the difference between line and phase voltage?

A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

What are the losses in a transmission line?

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line

A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

Series capacitive compensation in EHV transmission line is used to

A lightening arrester connected between the line and earth in a power system  (1) protects the terminal equipment against travelling surges (2) protects the transmission line against direct lightening strokes (3) suppresses high frequency oscillations in the line (4) reflects back the travelling wave approaching it

Precise control of reactive current flow entering the transmission and distribution systems can be minimized by using (A) synchronous condenser (B) static VAR capacitor (C) capacitor bank (D) thyristor switched reactor in parallel with capacitor

What is the meaning of Electronics and Communication Engineering?

What is the difference between a switch and a relay?

The voltage of transmission can be regulated by  (A) Use of tap changing transformers (B) Switching in shunt capacitors at the receiving end during heavy loads (C) Use of capacitors to neutralize the effect of series reactance (D) Any of the above methods

What is the definition of electronic communication?

What is the difference between relay and contactor?

ln HRC fuse the time between cut-off and final current zero is called

What are the types of electronic communication?

Write the relation between phase and line current, phase and line voltage for Star connection.

Explain Inter-process Communication (IPC) using mailbox/queue.

The reactive power transfer over a line mainly depends on

The surge impedance for over head line is taken as  (1) 10-20 ohms (2) 50-60 ohms (3) 100-200 ohms (4) 1000-2000 ohms

Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

lf a travelling-wave travelling along a loss-less overhead line does not result in any reflection after it has reached the far end, then the far end of the line is

What is the difference between a soft start and a VFD?

What is the difference between an anode and a cathode?

What is the difference between an insulator and a dielectric?

What is the difference between a sensor and a transducer?

What is the difference between a microcontroller and a microprocessor?

What is the difference between a mesh and a loop?