# Which relay is preferred for phase fault on short transmission line?

17 views

Reactance relay is preferred for phase fault on short transmission line.

## Related questions

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

what is mean by short transmission line ?

In which fault the maximum short circuit current occurs?

If the % reactance upto the fault point is 20%, then the short circuit current will be

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line

If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) zero sequence currents are absent on both sides of the transformer  (C) zero sequence currents are present on the secondary side but not on the primary side  (D) zero sequence currents are present on the primary side but not on the secondary side

The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)  (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents

Transmission efficiency of a transmission line increases with the

A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9

The sag of a transmission line is least affected by (A) Self weight of the conductor. (B) Temperature of the surrounding air. (C) Current through the conductor. (D) Ice deposited on the conductor.

A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km

Series capacitive compensation in EHV transmission line is used to

what is mean by medium transmission line ?

what is mean by long transmission line ?

Reactance relay is normally preferred for protection against

Stability of a transmission line can be increased by

What are the losses in a transmission line?

Write the relation between phase and line current, phase and line voltage for Star connection.

For 11kV line the inductance per km per phase will be of the order of:  (A) 1 H (B) 0.1 H (C) 1 mH (D) 0.1 mH

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be

What is line voltage and phase voltage? Draw balanced three phase star connected system. Show all the voltages and currents.

What is the difference between line and phase current?

What is the difference between line and phase voltage?

What is the voltage in 3 phase line?

Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

Which is the most common type of fault?

In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be

A relay used for protection of motors against overload is :  (A) Impedance relay (B) Electromagnetic attraction type (C) Thermal relay (D) Buchholz's relay

A negative sequence relay is used for protection of  (1) Generator (3) Motor (2) Transformer (4) Long Transmission lines

With fault clearing time, the transient stability of a power system

To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed