# The standard full-load power factor ratings for synchronous motors are?

16 views

The standard full-load power factor ratings for synchronous motors are unity or 0.8 leading.

## Related questions

If the load of the normally excited synchronous motor is increased the power factor will?

The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

If we change the excitation of synchronous machine will it affect on power factor?

If the field of synchronous motor is under excited, power factor will be?

A synchronous motor has better power factor as compared to that of an equivalent induction motor. This is mainly because?

In a synchronous generator delivering lagging power factor load  (1) the excitation emf leads terminal voltage by the power angle (2) the excitation emf lags terminal voltage by the power angle (3) excitation emf leads the terminal voltage by the power factor angle (4) excitation emf lags the terminal voltage by the power factor angle

The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are (A) 0.5 pu, 0.866 pu (B) 0.866 pu, 0.5 pu (C) 0.707 pu, 0.707 pu (D) 0.5 pu, 0.5 pu

Can a synchronous condenser improve power factor?

How can we improve power factor using synchronous motor?

The synchronous motor will develop maximum power when the load angle is?

What is the difference between synchronous and asynchronous motors?

Damper winding is provided in 3 phase synchronous motors to :

The efficiencies of transformers compared with that of electric motors of the same power are?

Why the power factor of semiconverter is better than full converter?

A three-phase synchronous motor connected to ac mains is running at full load and unity power factor. lf its shaft load is reduced by half and field current is held constant then its new power factor will be

Capacitors for power factor correction are rated in?

Minimum voltage regulation occurs when the power factor of the load is?

At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

A transformer has negative voltage regulation when its load power factor is   (1) Zero (2) Unity (3) Leading (4) Lagging

Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is  (1) 122.8 GWh (2) 198.55 GWh (3) 128.2 GWh (4) 188.82 GWh

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Draw and explain bulk correction method for power factor & control.

The armature reaction in a synchronous generator supplying leading power factor load is (A) magnetizing (B) demagnetizing (C) demagnetizing and cross-magnetizing (D) magnetizing and cross-magnetizing

The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is (A) 0.25 pu (B) 0.5 pu (C) 1.0 pu (D) 1.5 pu

The standard for long distance analog signal transmission in process control industry is (A) 4-20 mV (B) 0-20 mA (C) 4-20 mA (D) 0-5 V

State the incentives and penalties related with power factor tariff.

State the significance of power factor.

The power factor of dielectric :  (A) is a function of temperature of the dielectric only (B) depends only on voltage stress to which the dielectric is stressed (C) always constant (D) both (A) and (B)

The benefit of power factor correction in a power system is (A) lower power consumption (B) increased demand charge (C) reduced load carrying capabilities in existing lines (D) reduced voltage profile

The power factor of a D.C. circuit is always?

The ratio of active power to apparent power is known as____ factor.