# A three point starter is considered suitable for?

17 views

## 1 Answer

0 votes

A three point starter is considered suitable for shunt as well as compound motors.

## Related questions

1 answer 23 views
1 answer 17 views

what is the difference between four point starter and three point starter?

1 answer 18 views
1 answer 13 views
0 answers 13 views

What is an auto transformer starter?

0 answers 32 views

Why starter is required for starting an induction motor?

1 answer 14 views

A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

1 answer 21 views

The operating point of a protective current transformer is near the

1 answer 21 views

Blind spot is a point in the zones of protection where

1 answer 39 views

How is a three phase cage induction motor self starting?

1 answer 34 views
1 answer 8 views
1 answer 40 views

If the % reactance upto the fault point is 20%, then the short circuit current will be

1 answer 60 views

The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is

1 answer 58 views

What is mean by plugging in three phase induction motor?

0 answers 24 views

Which type of starter is used to start the DC motor?

0 answers 20 views

What is the best Arduino starter kit?

1 answer 63 views

State any four advantages of soft starter.

1 answer 86 views

State function of starter and ELCB. (Earth Leakage Circuit Breaker)

1 answer 80 views

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

1 answer 23 views

When a V-V three phase transformer system is converted into a Δ-Δ system, increase in capacity of the system is (A) 86.6% (B) 50% (C) 57.7% (D) 73.2%

1 answer 25 views

In a three-phase supply floating neutral is undesirable because it way give rise to?

1 answer 50 views

What is a three phase connection?

1 answer 23 views
1 answer 18 views

A 4—point starter is used to start and control the speed of a  A) DC shunt motor with armature resistance control B) DC shunt motor with field weakening control C) DC series motor D) Thyristor controlled d.c. motor

0 answers 9 views

List three important characteristics of an electric circuit.

1 answer 4 views

Define balanced and unbalanced load in three phase circuit.

1 answer 36 views

State any four applications of three phase circuits.

1 answer 58 views

Draw the waveform of three phase AC supply voltage.

2 answers 64 views

State any four advantages of three phase over single phase.

1 answer 18 views

When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

1 answer 23 views

Three phase synchronous motor will have how many sliprings?

0 answers 18 views

What are three ways you can increase the strength of an electromagnet?

0 answers 29 views

Explain power relations in three phase circuit.

1 answer 58 views

Explain three phase half wave controller or three phase unidirectional controller.

1 answer 86 views

Explain Three Phase Bidirectional Delta Connected Controller.

1 answer 44 views

Explain three phase bridge inverter.

1 answer 71 views

Explain three phase full wave controller.

1 answer 38 views

three phase to single phase cycloconverter

1 answer 29 views

how can we reverse the direction of rotation of three phase induction motor ?

0 answers 21 views

An electrodynamic wattmeter is not considered suitable for low power factor circuits because of (A) Inductance of voltage coil (B) Reactance of current coil (C) Power loss in voltage coil (D) Power loss in current coil

1 answer 32 views

A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for

1 answer 9 views

Which type of motor is most suitable for computerprinter drive?  A) Reluctance motor B) Hysteresis motor C) Shaded pole motor D) Stepper motor

1 answer 27 views

For using regenerative breaking, the most suitable motor is :  (A) DC series motor  (B) Slip ring induction motor  (C) Squirrel cage induction motor  (D) Synchronous motor

0 answers 65 views

Write short notes on 3 phase AC system.

1 answer 6 views

Describe the importance of three wire and four wire configuration for RTD with suitable circuit diagram.

1 answer 19 views
1 answer 9 views

Three different points are shown on a dc load line. The upper point represents the : -  a) minimum current gain b) quiescent point c) saturation point d) cutoff point

1 answer 14 views

Why is it that protons are not considered a source of moving charges for current flow?

1 answer 14 views

The number of cross -points needed for 10 lines in a cross-point switch which is full duplex in nature and there are no self connection is  A) 100 B) 45 C) 50 D) 90