14 views
in Electrical Machine by

1 Answer

0 votes
by

In D.C. machines the residual magnetism is of the order of 2 to 3 percent.

Related questions

2 answers 43 views

In dc machines, the armature windings are placed on the rotor because of the necessity for  (1) electromechanical energy conversion (2) generation of voltage (3) commutation (4) development of torque

asked May 1, 2018 in Electrical Machine by Shimroz123
1 answer 18 views

As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit?

asked Mar 20, 2018 in Electrical Machine by Shimroz123
1 answer 19 views

The process of removing the unwanted magnetism is called ______ A) Unmagnetization B) Degaussing C) Diamagnetization D) Depoling

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 24 views

The magnetic factor required to reduce the residual magnetization zero is called?

asked Mar 17, 2018 in Electrical Engineering by Quiz
1 answer 55 views

The inertia constants of two groups of machines which do not swing together are M1 and M2. The equivalent inertia constant of the system is

asked May 3, 2018 in Electrical Machine by Shimroz123
1 answer 25 views

A transfer function has a second order denominator and constant gain in the numerator

asked May 3, 2018 in Control System by Shimroz123
1 answer 308 views

In order to regulate steady state error to zero, in a negative feedback control system, one employs

asked May 1, 2018 in Control System by Shimroz123
1 answer 21 views

A second order system shows 100% overshoot in its unit step response. It can be categorized as (A) underdamped system. (B) overdamped system. (C) Critically damped system. (D) undamped system.

asked Apr 28, 2018 in Control System by Shimroz123
1 answer 34 views

Cells are connected in series in order to?

asked Mar 16, 2018 in Electrical Engineering by Quiz
1 answer 29 views

Silicon steel is used in electrical machines because it has?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

asked Mar 20, 2018 in Electrical Machine by Shimroz123
1 answer 66 views

For protection of rotating machines against lightning surges _______ is used.  (1) lightning arrester (2) capacitor (3) combination of lightning arrester and capacitor (4) lightning conductor and arrester

asked Apr 30, 2018 in Switchgear And Protection by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...