The center of gravity of a uniform lamina lies at?

16 views

The center of gravity of a uniform lamina lies at?

The center of gravity of a uniform lamina lies at the mid point of its axis.

Related questions

The center of gravity of a triangle lies at the point of?

Center of gravity of a thin hollow cone lies on the axis at a height of?

Center of gravity of a solid cone lies on the axis at the height?

If a suspended body is struck at the center of percussion, then the pressure on die axis passing through the point of suspension will be?

The center of percussion of the homogeneous rod of length L suspended at the top will be?

Center of percussion is?

The skin effect in conductors is due to non uniform distribution of current in it and major portion of current is near the _______ of conductor.  (1) Surface (2) Center (3) Complete cross section area (4) Axis

Which of the following is the name given to resistance of thin films that are uniform in thickness? A) Area resistance B) Sheet resistance C) Filmy resistance D) None of these

Write one advantage and one disadvantage each for spring control method and gravity control method.

The forces, which meet at one point, but their lines of action do not lie in a plane, are called?

The resolved part of the resultant of two forces inclined at an angle 9 in a given direction is equal to

A number of forces acting at a point will be in equilibrium if?

During charging, the specific gravity of the electrolyte of a lead acid battery _____.

In root locus plot, a point on the real axis lies on the locus, if the number of open loop poles plus zeros on real axis to the a) left of the point is odd b) left of the point is even . c) right of the pointis odd d) right of the point is even

Whether a given point in the S-plane lies on the Root Locus of a system can be determined by (A) Magnitude criterion (B) Angle Criterion (C) Both Magnitude and Angle Criteria (D) Break-in and Break-away Criteria

If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is   (a) 33.2 V/cm (b) 0.03 cm/V (c) 66.4 V/cm (d) 0.015 cm/V

What is the resistance of a 160 m wire with a uniform diameter of 0.28 mm, if the specific resistance is 12.32 μΩ-cm? A) 3.2 Ω B) 3.2 μΩ C) 0.8 Ω D) None of these

The non-uniform distribution of voltage across the units in a string of suspension type insulators is due to?

If two equal forces of magnitude P act at an angle 9°, their resultant will be

A constant load power means a uniform conversion of? A.mechanical to electrical energy B.electrical to mechanical energy C.current to voltage D.voltage to current

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

The use of non-uniform quantization leads to: (1) Reduction in transmission bandwidth. (2) Increase in maximum SNR. (3) Increase in SNR for signal levels. (4) Simplification of quantization process.

The scale of meter is uniform. Its type is  A) moving iron B) Induction C) moving coil permanent magnet D) moving coil dynamometer

On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be?

On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be?

A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20 meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span?

If a rigid body is in equilibrium under the action of three forces, then?

According to principle of transmissibility of forces, the effect of a force upon a body is?

The weight of a body is due to

The algebraic sum of the resolved parts of a number of forces in a given direction is equal to the resolved part of their resultant in the same direction. This is as per the principle of

The critical point lies within the nyquist plot then the system is   (a) Marginally stable (b) Unstable (c) Stable (d) Undetermined

How can you create a uniform appearance by adding a background image to all slides?  (1) Create a template (2) Edit the slide master (3) Use the autocorrect wizard (4) All of these

On Smith chart, the eccentric circle passing through the prime center represents (in Ohms)  A) R=0 B) R=1 C) Xc=0 D) R=infinity

If a number of forces act simultaneously on a particle, it is possible?

A single force and a couple acting in the same plane upon a rigid body?

The algebraic sum of moments of the forces forming couple about any point in their plane is?

Limiting force of friction is the?

Coefficient of friction is the?

The ratio of limiting friction and normal reaction is known as?

The coefficient of friction depends on?

Angle of friction is the?